Service HotlineThe hinge is a hinge, which is often composed of two folds. It is a part that connects the two parts of the object and can make it move. The hinge supporting screws are installed on the corresponding objects. For different use environments, the requirements for the supporting screws are also different. different. Most of the existing screws are set to a single-threaded structure. When used to cut into a wooden door, the cutting speed is slow, and the cutting effect is not ideal, which is not conducive to cutting into a hard wooden door, etc., and the commonly used screws are often made of iron materials. It is easy to rust after contact with water vapor, reducing the service life; in addition, when the screw is driven into the wooden door, the chips generated cannot be discharged in time, and stay inside the wooden door and surround the screw, forming expansion stress, thereby squeezing the wooden substrate, which is not conducive to the screw. The connection with the wooden door is stable, which easily affects the normal installation of the hinge, and the use effect is poor. To sum up, in order to solve the shortcomings of the existing screw structure for hinges, Guangdong Yueluo Hardware Industry Co., Ltd. designed a hinge screw with simple structure, convenient use, fast construction and good effect.
Yueluo also provides a thin plate rivet structure, which includes a metal thin plate and a rivet. The metal sheet is provided with a riveting hole; the riveting piece is penetrated in the riveting hole, the outer edge of the riveting piece is provided with an occlusal structure, and the inner edge of the riveting hole is embedded with the occlusal structure. A deformation groove is provided on the metal sheet, and the deformation groove is adjacent to the rivet hole.
Guangdong Yueluo Hardware Industry Co., Ltd. provides a kind of rivet, parts and parts are riveted by the rivet, the part has a fixed plate and a fixed plate, and the part is located between the fixed plate and the fixed plate, The rivet includes a nail head, a nail post and a nail post which are connected in sequence, the diameter of the nail post is larger than the diameter of the nail post, the nail head is matched with the outer end surface of the fixing plate, and the length of the nail post is It is greater than the sum of the riveting length of the fixing plate and the riveting length of the part. The rivet can control the distance between the parts, so that the relative rotation of the two parts is more smooth and easy to operate.
The flat screw mainly includes a rotating part and a screw locking part, wherein the rotating part and the screw locking part are respectively flat-shaped structures; At least two sides of the screw lock portion are respectively provided with tooth rows, and the two tooth rows are mutually dislocated, so that the screw lock portion can be locked in a pre-formed screw hole in the workpiece.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB5783 hexagon screws, flat washers used on the front and back, screws with washers, stainless steel 304 bolts and other products, we can provide you with fastening suitable for you piece solution.
