Service Hotlinesafety screw includes a screw rod, and is characterized in that: the two ends of the screw rod are respectively provided with notches for rotating a tool knife. Compared with the prior art, the advantage of Guangdong Yueluo Hardware Industry Co., Ltd. is that notches are provided at both ends of the screw, so that when the screw is in use, it can be tightened or loosened from both ends without installation. Due to the limitation of position and structure, when the installation space is small or the tool knife cannot be inserted, it is convenient for the operator to directly tighten or loosen the screw from the other end, which improves the efficiency of installation and disassembly, saves assembly time and reduces assembly difficulty.
Standard screw is one of the fasteners commonly used for fastening and assembly. Standard screws and flat washers, grade A, and standard spring washers, are used in combination, and are widely used in the assembly of various products. For manufacturers who use combination screws in small and medium batches, the process of combining screws, spring washers and flat washers generally adopts the method of assembling screws by workers' bare hands. This method is tedious and repetitive, wastes human resources, is time-consuming and labor-intensive, and it is difficult to ensure the normal operation of the workshop. assembly progress. The screw assembly machines currently on the market can replace manual assembly screws, but this type of equipment has disadvantages such as bulky size, high cost, complex structure, inconvenient non-standard manufacturing and maintenance, high noise, and power consumption.
A pin and a pin piece inserted on the pin, the width of the pin piece gradually decreases from the insertion end to the other end, and the pin piece is also provided with a protrusion, the protrusion is a triangular ratchet tooth shape, the An insertion hole is arranged on the pin, and a pawl corresponding to the protrusion is arranged in the insertion hole.
Fasteners are widely used in nuclear power plant safety systems and equipment, and undertake the functions of component connection, pressure sealing box support and fixation, and their quality and performance play an important role in nuclear power plant safety systems and equipment performing nuclear safety functions. None of the special fasteners for nuclear power in the prior art have protective sleeves, which cannot protect the exposed part of the bolt shank. In order to solve the above difficulties, it is necessary to develop a fastener stud nut washer set that can protect the exposed part of the bolt shank.
Anti-corrosion technology Stainless steel screws are made of metal, and there are four main methods for metal anti-corrosion, namely the properties of the material itself, the environment of use, the interface between materials and the environment, and the improvement of the metal structure design. If a complete anti-corrosion alloy is used to make stainless steel Screws, unless there is a special need, are not cost-effective in terms of economics, and it is also impractical to completely isolate the appearance of the screw from environmental elements that can cause corrosion. Improving the metal structure design can improve the influence of special circumstances under certain conditions, but the design of most stainless steel screws cannot be fully corrected, and its maintenance effect is not permanent, so this method cannot basically solve the problem, as long as it is on the surface. Top anti-corrosion, that is, surface anti-corrosion treatment is the most widely used method. The anti-corrosion treatment on the surface of stainless steel screws refers to the use of various methods to apply a protective layer on the metal surface. The purpose of avoiding or mitigating corrosion. The protection layer should be able to meet the following requirements: 1. Corrosion resistance, wear resistance, high hardness, 2. The structure is tight, intact, and the pores are small. 3. It has strong separation and good adhesion with the base metal. 4. It is evenly distributed and has a certain thickness. The maintenance layer is usually divided into two types: metal coating and non-metallic coating. Metal coating refers to the use of metal or alloy with strong corrosion resistance to form a maintenance layer on the surface of metal that is easy to corrode. This coating is also called plating. There are quite a few methods and varieties to produce metal coatings, the most common of which is electroplating, followed by molten metal immersion plating (hot dipping) and chemical surface treatment. Non-metallic coating refers to the use of organic polymer materials such as paint and inorganic materials such as ceramics to form a protective layer on the surface of metal equipment or parts. The protective layer can completely isolate the base metal from the environmental medium and prevent the base metal from corrosion due to contact. Corrosion is formed in the medium of stainless steel standard parts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: copper rivets, 201 hex bolts and nuts, aluminum T-nuts, fastener screws and other products, we can provide you with suitable products for you. Fastener Solutions.
