Service HotlineRivet riveting has the advantages of simple process equipment, shock resistance, impact resistance, uniform force transmission, firmness and reliability, etc. The key parts of mining equipment such as skips, cages, dumpers, and mine trucks are all connected by rivet riveting. The quality of rivet riveting directly affects the product quality, working performance and service life of mining equipment. The number of rivets used in mining equipment is huge. Each mining equipment requires one hundred or hundreds of rivets, and they are used in mining equipment. The specifications of the rivets in the equipment are large, and the riveting process of hot riveting is mostly used. The riveting tools required are riveting machines and rivet molds.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
The front wall sound insulation pad is used to absorb the heat and noise transmitted by the firewall, and also plays the role of heat insulation and vibration isolation, ensuring a relatively quiet and comfortable environment in the car and improving ride comfort. As shown in FIGS. 1 and 2 , the front wall sound insulation and heat insulation pad 101 is generally fixed to the vehicle body by means of screw buckles 102 . The screws 100 are clamped by the clamping feet 103 in the screw The limiting rib 104 clamps the screw 100. After the screw 100 is clamped into the screw buckle 102, the tail end of the screw 100 is exposed, which is easy to scratch the operator when assembling other components, and the exposed screw 100 is easy to cause corrosion, thereby affecting the connection strength of the screw 100, and also The service life of the screw 110 is reduced.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of quality also contributes to the improvement of the lifespan of the 9 bottles.
For common screw belts, please refer to the Central Taiwan Announcement No. 327442 Screw Belts (2) on February 21, 1998. It includes a main body, and there are multiple grooves on the side of the main body, which are used for locking screw tools to drive the belt. A toggler; and a plurality of nail grooves are arranged on the nail belt so that the screw planting is arranged in an arrangement, and the nail grooves are all provided with through holes, and the through holes extend downward with a ring to form a support portion for the screws; and the It is surrounded and provided with a plurality of cutting grooves, which is beneficial for the screw to be rotated through the nail groove; and it is characterized in that the nail groove is located on the inner wall surface of the surrounding and is provided with a plurality of lobes, and these lobes are implanted in the screw. In the nail groove, the leaflet supports the screw, so that the screws with different outer diameters are fully supported and positioned by the leaflet; and/or the upper part of the leaflet is inclined or curved, so that a depression is formed above the ring to support the screw The arc surface or tapered surface of the neck can make the screw more stable to be supported.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Phillips socket head cap screws, extended cup head socket head cap screws, flat head screws nuts, long nuts and other products, we can provide you with suitable products for you Fastener Solutions.
