Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a new type of open blind rivet suitable for riveting of aluminum Al, steel St, and stainless steel SST sheets with foam material in the middle. The new rivet improves the mandrel process, adopts aluminum mandrel, the head of the mandrel has a pit for easy deformation, and there is a conical stop groove above the breakpoint of the mandrel. The mandrel can be caught by the stopper to prevent the nail head from being exposed. At the same time, lock the core rod not to loosen.
(1) The screw-in performance test is to screw the self-tapping locking screw sample into the test plate until one complete thread completely passes the test without breaking. (2) The destructive torque test is to clamp the stem of the self-tapping locking screw specimen in a thread mold or other device that matches the screw thread, and uses a calibrated torque-measuring device to measure the screw. Torque is applied until fracture, which should not occur in the clamped threaded portion. (3) Carry out a tensile test on the screw sample to check the minimum tensile load for failure. The fracture should be within the length of the rod or the unthreaded thread, and should not occur at the junction of the nail head and the rod. Before the sample breaks, it should be It can reach the minimum tensile load specified by the corresponding performance class. (4) Hydrogen embrittlement is a problem that must be strictly paid attention to in the surface treatment process of self-tapping locking screws. In the pickling process, the screw is stirred in dilute hydrochloric acid, and the amount of hydrogen absorbed by the pickling steel increases linearly with the square root of time and reaches the saturation value. Less than 100%, a large number of hydrogen atoms will be produced, which will be attached to the surface of the screw, resulting in hydrogen infiltration, and the steel will become brittle due to the absorption of hydrogen. The self-tapping locking screw takes 6~8h to drive hydrogen, and the temperature is 160~200℃ (phosphating) and 200~240℃ (electroplating). However, in the production process, the hydrogen drive time should be determined according to many production conditions such as core hardness, surface roughness, electroplating time, coating thickness, pickling time, and acid concentration. It is best to do it before passivation and just after electroplating.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (10), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the deformation. effect.
A medical self-locking screw, wherein the medical self-locking screw is composed of an outer screw and an inner screw, the outer screw includes a fixedly connected fitting body and the front part of the outer screw, and the front part of the outer screw includes a fixed connection The outer screw rod body and the outer screw head are provided with fixed external threads on the periphery of the outer screw rod body, and a backstop ring is provided on the periphery of the matching body;
door cover structure with hidden screws includes a glass panel, an inner door cover, a computer board and a sealing strip, an adhesive bracket is adhered to the back of the glass panel, the inner door cover is fixedly connected with the adhesive bracket through screws, and the computer board is arranged on the glass panel. In the cavity formed by the panel and the inner door cover, the inner door cover is provided with a sealing slot, the sealing strip is embedded in the sealing slot, and the bottom of the sealing slot is provided with a mounting hole for the screw to pass through, and the glue The bracket is provided with a fixing hole matched with a screw thread, and the screw passes through the installation hole of the inner door cover and is threadedly connected with the fixing hole of the adhesive bracket, so as to fixedly connect the inner door cover and the glass panel. The screw is hidden in the sealing groove of the door cover, and is sealed with water through the sealing strip. The appearance is beautiful, easy to disassemble and assemble, and it can effectively protect the screw from rust.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: manual nuts, professional processing nuts, double-pass copper studs, processing cone pins and other products, we can provide you with suitable fasteners for you solution.
