Service HotlineLocking of screws belongs to the prior art. Or by means of a visual method (X-ray control) a more or less complex aiming device is inserted into the transverse hole of the screw. In both cases a certain misalignment is unavoidable, ie the screw may not be coaxial with the central axis of the transverse hole and deviate from it by a certain value. In order for the locking screw to pass into and through the transverse hole despite this misalignment, the outer diameter of the screw is determined to be a size smaller than the diameter of the transverse hole. If the aiming is not maintained within this small dimension value, the locking screw can pass through the transverse hole without difficulty despite the aiming error. Now, however, the locking screw has a certain clearance relative to the transverse hole due to the determination of a smaller size value.
National standard lock nut GB/T 6182-2000 Type 2 non-metallic insert hexagonal lock nut. GB/T 6183.1-2000 Non-metallic insert hexagonal flange lock nuts. GB/T 6183.2-2000 Non-metallic insert hexagonal flange lock nuts - fine pitch. GB/T 6184-2000 Type 1 All-Metal Hexagon Lock Nuts. GB/T 6185.1-2000 Type 2 all-metal hexagonal lock nuts. GB/T 6185.2-2000 Type 2 all-metal hexagonal lock nuts with fine teeth. GB/T 6186-2000 Type 2 All-Metal Hexagon Lock Nuts Grade 9. GB/T 6187.1-2000 All-metal hexagonal flange lock nuts. GB/T 6187.2-2000 All-metal hexagonal flange lock nut with fine teeth. GB/T 889.1-2000 Type 1 non-metallic insert hexagon lock nuts. GB/T 889.2-2000 Type 1 non-metallic insert hexagonal lock nut fine pitch.
Semi-round head plastic screws have high-quality characteristics such as insulation, non-magnetic, corrosion resistance, beautiful appearance, and never rust, and modified engineering plastics, its strength and impact resistance are comparable to those of metals. The plastic screws we often say are commonly known as nylon. After adding 30% glass fiber to the screw, its mechanical properties are far superior to ordinary nylon. The materials used for the dome head plastic screws are becoming more and more diverse, the performance is constantly improving, and the application fields are becoming wider and wider. 1. Medical equipment industry (insulation, non-magnetic, environmental protection, anti-interference, make medical equipment safer to use) 2. Wind power industry (isolation and insulation of chassis circuit PCB boards) 3. Aerospace industry (electronic equipment Insulation, anti-interference) 4. Office equipment industry (never rust, beautiful and practical) 5. Petrochemical industry (high temperature resistance, chemical resistance, corrosion resistance, prolong equipment life) 6. Electronics industry (insulation, anti-interference) , light weight) 7. Communication industry (insulation, non-magnetic, safety) 8. Ship industry (acid resistance, alkali resistance, corrosion resistance, extended service life), etc... .
Several concepts about high-strength bolts 1. According to the specified performance level of bolts above 8.8, they are called high-strength bolts. The current national standard only lists M39. For large-size specifications, especially those with a length greater than 10 to 15 times High-strength bolts, domestic production is still short-term. The difference between high-strength bolts and ordinary bolts: High-strength bolts can withstand larger loads than ordinary bolts of the same specification. High-strength outer hexagon bolts High-strength outer hexagon bolts are made of Q235 (ie A3). The material of high-strength bolts is 35# steel or other high-quality materials, which are heat-treated after being made to improve the strength. The difference between the two is the difference in material strength. From raw materials: High-strength bolts are made of high-strength materials. The screws, nuts and washers of high-strength bolts are all made of high-strength steel, such as No. 45 steel, 40 boron steel, 20 manganese titanium boron steel, 35CrMoA, etc. Ordinary bolts are usually made of Q235 (equivalent to A3 in the past) steel. In terms of strength grades: high-strength bolts are increasingly used. Two strength grades are commonly used, 8.8s and 10.9s, of which 10.9 is the majority. The strength level of ordinary bolts is lower, generally 4.4, 4.8, 5.6 and 8.8. High-strength bolts High-strength bolts are viewed from the force characteristics: high-strength bolts apply pretension and transmit external forces by friction. Ordinary bolt connection relies on the shear resistance of the bolt and the bearing of the hole wall to transmit the shear force. When the nut is tightened, the pre-pressure is very small, and its influence can be ignored. In addition to its high material strength, high-strength bolts also exert a large amount of pressure on the bolts. The pre-pressure generates extrusion force between the connecting components, so that there is a large friction force perpendicular to the direction of the screw, and the pre-pressure, anti-slip coefficient and steel type directly affect the bearing capacity of high-strength bolts. According to the force characteristics, it is divided into pressure type and friction type. The calculation methods of the two are different. The minimum specification of high-strength bolts is M12, and M16~M30 are commonly used. The performance of super-large bolts is unstable and should be used with caution in design.
The material of the second combination screw: It is decided to use the test machine to test the material of the combination screw wire, which is divided into iron and stainless steel. Iron wire is divided into 1010 wire and 1018 wire, 10B21 wire, etc., stainless steel is divided into stainless steel 201, stainless steel 304, stainless steel 316 and so on. The provisions of the national label of three combination screws: Generally, those who have experience in combination screws can be separated by using the inner eye. The difference between hexagon heads. Use a caliper to measure out the three-combination screw specifications. How big is it, how long is it, how thick is the head of the combination screw, how thick is the flat washer, and what is the outer diameter of the flat washer. How many hours is the salt spray of the combination screw measured with a salt spray machine. Use the environmental test machine to test whether the three-combination screw is environmentally friendly. Still not environmentally friendly.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 304 fasteners stainless steel bolts, hexagon socket screws, machine screws, knurled taper, conical nuts and other products, we can provide you with suitable Your fastener solution.
