Service HotlineDue to the high demand for electronic products and the reduction of assembly line workers, in order to cope with the problem of labor shortage, manufacturing factories need to use automatic screw locking equipment to replace manual labor. In the existing automatic locking and paying equipment, most of them use a screw arranging machine to arrange the screws, and an electric screwdriver (electric batch) takes the screws back and forth, or the special equipment blows the screws into the electric batch to send the screws to the electric batch, and back and forth. The method of taking is too time-consuming, and the method of blowing air is not suitable for screws with small aspect ratios.
Due to the high demand for electronic products and the reduction of assembly line workers, in order to cope with the problem of labor shortage, manufacturing factories need to use automatic screw locking equipment to replace manual labor. In the existing automatic locking and paying equipment, most of them use a screw arranging machine to arrange the screws, and an electric screwdriver (electric batch) takes the screws back and forth, or the special equipment blows the screws into the electric batch to send the screws to the electric batch, and back and forth. The method of taking is too time-consuming, and the method of blowing air is not suitable for screws with small aspect ratios.
As we all know, when installing the outdoor unit of the air conditioner, most of the installers need to hang it on the outer wall. When tightening the machine foot screws, they all need to lean out of the window or climb out the whole person, and use a wrench to tighten it. . Therefore, it is difficult for the installer to operate, and it is easy to drop the installation materials such as screws and nuts, which is not only a waste of materials, but also easy to hurt personnel. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to solve the above problems, and provide a safe and labor-saving air conditioner outdoor unit machine foot screw installer that the installer does not have to lean out of the window or climb out of the room, and the installation materials are not easy to fall.
Bolts with low hardness and strength. Generally, ordinary bolt materials are produced with ordinary screw wires. The hardness, strength, tensile strength and torsion force of ordinary bolt materials are not very high. High-strength bolts generally refer to high-strength bolts. Its own screw material, bolt material, and bolt material are relatively good, and the hardness is relatively high, and after the production is completed, the bolts will be hardened. Make the bolts meet the grade strength requirements of high-strength bolts.
(1) The surface rust, oil stains, burrs on the wall of the bolt holes, welding flashes, etc. should be cleaned up. (2) After the contact friction surface is treated, the specified anti-scratch coefficient requirements must be met. The high-strength bolts used should have matching nuts and washers, which should be used in accordance with the matching and should not be interchanged. (3) When the friction surface of the treated component is installed, it is not allowed to be stained with oil, soil and other sundries. (4) The friction surface of the module should be kept dry during installation and should not be operated in the rain. (5) Strictly check and correct the deformation of the connected steel plates before installation. (6) It is forbidden to hammer into the bolt during installation to prevent damage to the bolt thread. (7) The electric wrench, which is regularly tested during use, ensures the accuracy of the torque and operates in the correct tightening sequence. Main safety technical measures (1) The size of the wrench of the adjustable wrench should be consistent with the size of the nut, and the sleeve should not be added to the small wrench. A dead wrench should be used for high-altitude work. For example, when using an adjustable wrench, use a rope to fasten it, and people should fasten their seat belts. (2) When assembling the connecting bolts of steel components, it is strictly forbidden to insert your hands into the connecting surface or touch the screw holes. When picking and placing the bolster, your fingers should be placed on both sides of the bolster.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: cross groove external hexagon three-combination bolts, copper embedded nuts, round cup head hexagon socket bolts, GB838 screws and other products, we can provide you with suitable products. Your fastener solution.
