Service HotlineIn the existing life, repair parts are often used to repair the cassettes with damaged screw holes, and the screw holes on the repair parts are used instead of the original damaged cassette screw holes. However, in the prior art (application number: 201520948368.1), the restoration is fixed by rotating the support of the restoration, which is often inconvenient due to the small space of the cassette. In addition, the set screw in the prior art mainly fastens the object through the end of the screw without threaded holes, which makes it difficult to install external screws. Based on this, a method of extruding the support through a set screw with screw installation holes and tightening the repair piece, and then installing the screw on the set screw, will facilitate the quick installation and use of the repair piece.
At present, shaft retaining rings are mainly divided into three categories: elastic retaining rings for shafts, flattened wire retaining rings for shafts, and wire retaining rings for shafts. Among them, the spring retaining ring for the shaft is generally installed with circlip pliers, and the flattening wire retaining ring for the shaft and the wire retaining ring for the shaft are generally installed with a sharp screwdriver or needle-nose pliers. The defects and deficiencies of these two methods will be discussed in detail below: First, the above two installation methods require the operator to use a large force to open the retaining ring, which is more laborious; For the installation of the flattened steel wire retaining ring for the shaft and the steel wire retaining ring for the shaft, because the wire retaining ring has low elasticity and has no force point, it is very easy to cause the retaining ring to break or the installation tool to slip during the installation process. Higher skills and experience can be competent for the installation of wire retaining rings.
In the prior art, there are two ways to feed the screws of the locking screw machine, the air blowing type and the air suction type. The air suction type is suitable for relatively small screws. If the screw size is larger than M2, smaller than M5, and the length-diameter ratio is larger than 1.4, the air-blown screw machine can be selected.
Contents of the utility model Guangdong Yueluo Hardware Industry Co., Ltd. is to solve the problem of needing one hand to hold the screw when screwing the screw at present, and to provide a screw fixture that can screw the screw without holding the screw by hand. Guangdong Yueluo Hardware Industry Co., Ltd. adopts the following technical solutions. Guangdong Yueluo Hardware Industry Co., Ltd. includes a clamp sleeve, and the middle of the clamp sleeve is a through hole. The outer end of the pivot pin is in contact with the spring. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is because Guangdong Yueluo Hardware Industry Co., Ltd. is provided with a rotating pin on the shaft of the fixture sleeve that can contact the screw, and the outer end of the rotating pin is in contact with the spring, so that the screw It is easy to fix in the through hole of the fixture cover, and the screwdriver is also in the through hole of the fixture cover, which ensures the alignment of the screw and the screwdriver, so it is avoided to hold the screw by hand, and the screw is quickly screwed to the object. in vivo.
The profile of the American National thread (60 profile angle and H/8 flatness) is different from the Wyeth thread profile (55 profile angle and H/6 flattening height). American National Thread is widely used in regions and industries that are influenced by American industry. In World War II, due to the inconsistent thread standards used by the Allies, the logistical supply difficulties caused serious economic losses and casualties to the Allies. Immediately after the end of World War II, the United States, the United Kingdom, Canada and other allies immediately began to formulate a unified thread standard among allied countries, and promulgated a unified thread standard in 1948. Because the economic strength and military strength of the United States dominated the Allied forces at that time, the unified thread was mainly formulated according to the national thread standard of the United States. Unity; the latter letter N is derived from the N designation for American National Threads. Since then, the unified thread began to squeeze the original use market of the British Whitworth thread.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal column yin and yang studs, hand-adjusted screws, semi-steel bolts, nylon self-locking nuts and other products, we can provide you with suitable tightening. piece solution.
