Service HotlineScrews are very small screws used for indispensable industrial necessities in daily life, such as cameras, glasses, clocks, electronics, etc.; general screws for televisions, electrical products, musical instruments, furniture, etc.; large screws are used for engineering, construction, and bridges; Transportation equipment, airplanes, trams, automobiles, etc. use large and small screws together. At present, in the machine assembly production line, when the flat washers, spring washers and screws are matched during the screw assembly process, the flat washers, spring washers and screws are easy to fall into the product due to their small size, resulting in low screw matching efficiency. If there are flat washers, spring washers, screws, etc. that fall into the product and are not found in time and left inside the product, it may cause damage to the machine structure, and even cause casualties in serious cases.
Other names of lock nut: root nut, locknut, nut. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures. There are also three types of lock nuts: The first is to use two identical nuts to screw on the same bolt, and add a tightening torque between the two nuts to make the bolt connection reliable. The second is a special anti-loosening nut, which needs to be used together with a kind of anti-loosening washer. The special lock nut is not a hexagonal nut, but a medium round nut. There are 3, 4, 6 or 8 notches on the circumference of the nut (depending on the size of the nut and the product series of the manufacturer). Several notches are both the focal point of the tightening tool and the snap-in of the lock washer bayonet. The third type is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, which are distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to give the thread Apply a centripetal force to prevent the locknut from loosening. The better quality lock nut sold on the market is inlaid with a small copper block that is consistent with the thread of the lock nut on the inner surface of the nut to prevent the radial jacking screw from directly contacting the locked thread and damaging the latter. . This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The second anti-loosening method is more reliable than the first, but the structure is relatively complex. Compared with the first two, the third clock has the characteristics of better anti-loosening effect, simpler and more beautiful structure and smaller axial size.
Wood screws are similar to machine screws, but the thread on the screw is a special thread for wood screws, which can be directly screwed into wooden components (or parts) to connect a metal (or non-metal) part with a through hole to a wood screw. The components are fastened together. This connection is also a detachable connection.
T-slot convenient bolt that can be used for the middle port of the T-slot and directly realizes the assembly and tightening of the bolt and the nut. Technical Background At present, the bolts for T-slots are assembled from two side ports of the T-slots. When the length of the T-slot is long, it is time-consuming and laborious to install from the side port to the center port at the designated position. In addition, the two side ports of the T-slot are often blocked by other components, and the bolts for the T-slot cannot be installed or removed without disassembling other components. The utility model makes some improvements to the prior art. SUMMARY OF THE INVENTION The purpose of the present invention is to provide a T-slot convenient bolt with simple structure and convenient mounting and dismounting for the current situation that the existing T-slot bolts are inconvenient to install and disassemble.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the deficiencies in the existing technology and provide a square nut fastener for cable tray installation, which has a simple and reasonable structure, and is extremely convenient and flexible to operate; it does not occupy C-shaped steel after installation. The space at the bottom increases the diversity of installation, and can be applied to square nuts of different thicknesses, and the installation is firm
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head chamfered hexagon socket nuts, 304 core blind aluminum countersunk head rivets, six-star plastic screws, hexagon socket headless screws and other products, we can Provide you with the right fastener solution for you.
