Service HotlineThe side wall of the bolt hole is threaded, and the top of the nut is provided with several flattening notches. According to the locking nut of the preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the number of flattening notches is three. Due to the above features, the three flattening notches can be used as the focal point of the tightening tool, and the
self-locking screw comprises a screw main body, a metal screw head is arranged on the upper part of the screw main body, a thread is arranged in the middle part of the screw main body, an interference groove is arranged on both sides of the upper part of the screw main body, and the line of the interference groove is arranged. The included angle is 280-356° with the horizontal line. The bottom of the screw body is provided with an elastic chuck, and the elastic chuck includes an optical axis and a conical head. Guangdong Yueluo Hardware Industry Co., Ltd. Guangdong Yueluo Hardware Industry Co., Ltd. adopts the design of elastic collet, and the screw is provided with threaded segments and interference grooves, so that during the screwing process, the interference groove of the optical axis between the two threaded segments is formed along the screw. The axial elastic force achieves the effect of reliable self-locking, which is easy to use and has high tuning efficiency.
At present, there are two methods for removing rivets in the market, one is non-destructive manual removal, which has low work efficiency and high work intensity. The other is mechanical destructive dismantling, such as the electric drill dismantling method. This method has high work efficiency, but it is easy to cause damage to the riveted product, and it is easy to cause the rivet to splash, and the operation is dangerous.
The structure of Guangdong Yueluo Hardware Industry Co., Ltd. is as follows. Figure 1 is a schematic diagram of the structure of the existing pin shaft stop mode of a general excavator. Figure 2 is a schematic structural diagram of the pin shaft stop used by Guangdong Yueluo Hardware Industry Co., Ltd. for applying the bolt of Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 3 is the left side view according to Fig. 2 of the bolt used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 4 is the front view of Guangdong Yueluo Hardware Industrial Co., Ltd., which is used for the pin shaft stopper to insert the pin into the pin and form the pin of the pin structure. Fig. 5 is the left side view of Guangdong Yueluo Hardware Industry Co., Ltd., which is used for the pin shaft stopper to insert the pin into the pin and form the pin of the pin structure. Fig. 6 is a front view of the bayonet of the latch used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 7 is a top view of a bayonet of a latch used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 8 is the front view of the circlip of the latch used by Guangdong Yueluo Hardware Industry Co., Ltd. for pin stop. [0017] FIG. 9 is a top view of the circlip of the bolt that Guangdong Yueluo Hardware Industrial Co., Ltd. is used for pin-stopping. In Figures 1 to 9, the latch (1), the retaining sleeve (2), the pin shaft (3), the bayonet (4), the circlip (5), the misaligned through hole (6), and the misaligned end head (7).
When the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: carbon steel nickel-plated European standard T-nuts, DIN316 butterfly screws and bolts, flat nuts, 12.9 blackened screws and other products, we can provide you with The right fastener solution for you.
