Service HotlineThe common types of wood screws are iron and copper, and the types are divided into round head type and other samples of wood screws according to different nail heads. There are two types of slotted screws and cross recessed screws. Generally, the round head screws are made of mild steel and are blue, and the flat head screws are polished. The oval head screws are usually plated with cadmium and chrome, and are often used to install hinges, hooks and other hardware accessories. Specifications are determined by rod diameter, length and nail head type. [1]
The screw rod in the ordinary T-slot nut is cuboid, so the T-slot nut can only be inserted into the nut from the end face of the T-slot, which makes it impossible to quickly complete the installation of the T-nut, which is inconvenient to use. Usefulness is greatly limited.
Installation method broadcast 1. One-time burying method: When pouring concrete, bury the anchor bolts. When the high tower is controlled by overturning, the anchor bolt should be buried once. 2. Reserved hole method: The equipment is in place, the holes are cleaned, the anchor bolts are placed in the holes, the equipment is positioned and aligned, and then poured with non-shrinkage fine stone concrete that is one level higher than the original foundation, and compacted and compacted. . The distance from the center of the anchor bolt once buried to the edge of the foundation should not be less than 2d (d is the diameter of the anchor bolt), and should not be less than 15mm (d≤20, it should not be less than 10mm), not less than half the width of the anchor plate Add 50mm, when the above requirements cannot be met, appropriate measures should be taken to strengthen it. The diameter of the anchor bolts used for the structure should not be less than 20mm. When subjected to earthquake action, double nuts should be used for fixing, or other measures to effectively prevent loosening should be adopted, but the anchorage length of anchor bolts should be increased by 5d compared with the anchorage length of non-seismic action. Installation planning of anchor bolts Treatment of anchor bolts loose in the foundation When the anchor bolts are tightened, the bolts may be pulled out. At this time, the bolts should be adjusted to their original positions, and the foundation around the bolts should be shoveled out enough. , and then weld two U-shaped steel bars vertically and horizontally on the bolts, and finally clean the pit with water and grouting, and then tighten the live anchor bolts after the concrete has solidified to the design strength. The treatment method of the live anchor bolt deviation is roughly the same as the dead ground. The method for the anchor bolts is the same, except that the anchor bolts can be pulled out for processing. If the bolt is too long, a section of the thread can be cut off on the machine tool; if the bolt is too short, it can be extended by hot forging; if the position is inconsistent, it can be corrected by bending. Application industry: suitable for various equipment fixing, steel structure foundation embedded parts, street lights, traffic signs, pump, boiler installation, heavy equipment embedded fixing, etc.
Electrical contact element is a kind of low-voltage electrical products and household electrical products widely used in switches, relays, thermostats, circuit breakers, contactors, controllers, timers, etc. There are mainly three types of electrical contact elements. 1. Riveting parts , riveting the rivet on the copper piece; 2. Welding piece, welding the sheet contact on the copper piece; 3. Stamping piece, punching the composite tape into components. Existing rivet contacts on the market at present are usually all made of precious metals, such as a simple metal matrix such as gold or silver. Its electrical contact performance is limited by a single metal material, and its electrical contact performance is poor; and due to certain requirements for metal purity in production, production efficiency is low, and production costs are high, resulting in the production of products that cannot be sold on a large scale in the market. and application.
4. Manufacturing and assembly Due to the limitations of manufacturing technology and accuracy, there are sharp corners on the edge of the thread or the dimensional coordination between parts is not coordinated. During the initial assembly, the screw-in and screw-out torque may fluctuate or fluctuate to a certain extent. After a certain number of running-in, more accurate reusability characteristics of the lock nut can be obtained.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagon nuts, GB807 galvanized nickel-plated flat head knurled hand nuts, external hexagon carbon steel screws, hexagon socket nuts and other products, we We can provide you with the right fastener solution for you.
