Service HotlineThe screw is usually installed in the threaded hole of the part, and its main function is to fix the relative position between the two parts. It is widely used in various industries. A traditional screw generally includes a screw rod and a head located at one end of the screw rod. During installation, the screw rod is connected with a threaded hole, and the head is located outside the screw hole and abuts on the edge of the screw hole.
In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35 , and the screws enter the screw accommodating hole 43 from the discharge port through the guide rail 6 . The slotting is carried out, which improves the efficiency and saves the labor cost.
Sometimes, the iron screws are often seen broken, and sometimes, the stainless steel screws are also seen broken. But generally speaking, stainless steel screws rarely break. Because the stainless steel screw wire itself is relatively hard. But under certain circumstances, stainless steel screws can still break. So what are the main reasons for stainless steel screws to break? The reasons for the fracture of stainless steel screws are as follows: 1. The quality of raw materials used for stainless steel screws is poor, and the quality of stainless steel screws is not good. There are many impurities, impure, resulting in insufficient hardness of stainless steel screws. 2. The production process of stainless steel screws. For example, stainless steel screws with eccentric head and eccentricity, and the Q value is too deep and the R position design is too small during the down punching operation during production. 3. The customer uses too much force when using stainless steel screws. Generally, you do a torque test to see how much the minimum breaking force is, and then adjust the torque. Of course, stainless steel screws must be broken for more than three reasons. But the above three reasons are the main reasons for the fracture of stainless steel screws. When the stainless steel screw is found to be broken, it can be checked step by step. Find out what's causing it.
As a commonly used data communication device, connectors are widely used in computers and TVs. Because common connectors such as D-SUB and DVI are composed of a male seat and a female seat, the iron shell of the male seat and the female seat is The corresponding position is provided with holes, the holes of the male seat are connected with rivets, and the holes of the female seat are correspondingly provided with screws for fixing. After the male seat and the female seat are connected, tighten the screws so that the male seat and the female seat are tightly connected together. When assembling on a computer or a TV, the rivet has a fixed assembly direction, and the fixation of the rivet direction is very important for assembly. However, there is no anti-rotation device on the iron shell hole connected with the rivet on the existing connector, and the rivet cannot be positioned during the assembly process, and it is easy to rotate and dislocate. production efficiency.
A kind of nut provided by Yueluo. The nut is in the shape of a casing and is provided with a threaded section. The hole walls at both ends of the threaded section are respectively provided with an annular shape and two grooves, and the notch of the groove points to the hole core. The hole diameter at the notch of the annular groove at the front end of the screw-in direction is larger than the nominal size of the thread segment, and the hole diameter at the notch of the annular groove at the rear end of the screw-in direction is smaller than the nominal size of the thread segment.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: threaded cylindrical pins, medium carbon 45 steel pins, pressure riveting nuts, Dongguan non-standard nuts and other products, we can provide you with suitable products for you. Fastener Solutions.
