Service HotlineIt can be seen from the figure that no matter how the screw core swings, it will not fall off from the screw sleeve. This is because part of the bead 5 is stuck in the hole 6 of the screw sleeve 1 and the other part is stuck in the screw core 2. In the groove 8, it plays the role of positioning. If the screw sleeve rotates clockwise, the beads 5 can only slide in the groove 8 of the screw core 2 under the driving of the screw sleeve 1 and cannot drive the screw core 2 to rotate. If the screw sleeve 8 rotates in the opposite direction, the bead 5 will be stuck on the stop 7 of the screw core 2 so as to drive the screw core 2 to rotate.
Most of the existing screws use an integral metal structure, and there are still some problems, such as large weight, high cost of materials, wear resistance, hardness, rust resistance, corrosion resistance, high and low temperature resistance, brittleness, toughness, etc. Many occasions cannot meet the needs of production, and further improvements are needed to improve production efficiency, reduce costs, improve safety, and prolong the service life of screws.
The beneficial effects of Guangdong Yueluo Hardware Industry Co., Ltd. are: the chip nut provided by Guangdong Yueluo Hardware Industry Co., Ltd. has a circle of serrated teeth protruding outward on the edge of the welding end face. During welding, excess solder After overflowing, it flows into the peripheral serrated convex tooth gap. In this way, on the one hand, the solder on the welding end face can be made uniform, and the welded chip nut can be neat and beautiful. On the other hand, the overflowed solder is combined with the serrated convex tooth gap. The welding area is increased, and the firmness and reliability of the welding are improved.
In order to tighten the fastener, the holding element of the tightening tool can hold the washer in engagement with the bolt to prevent the washer from rotating while allowing the rotating element of the tightening tool to rotate the nut. Such tools are disclosed, for example, in Application Serial Nos. 0/010377 and 10/120343. In this structure, since the same size washer cannot be arranged on the driving part and the fixing part, the driving part is made into the inner socket of the nut, and the fixing part is made into the outer socket of the washer, so , regular hexagonal nuts cannot be used. This is because, when just tightening the nut, the outer cavity cannot be removed since the hexagonal surface of the nut will not align with the hexagonal surface of the washer. Due to the larger diameter of the fastener formed as the outer cavity, side clearance problems may arise, thus increasing the cross-sectional profile of the hexagonal surface of the washer, which is undesirable.
Various stainless steel materials have different properties due to their different material contents, so the corrosion resistance is also different. The following is a brief explanation of several commonly used materials: 304 is a universal stainless steel, which is widely used in the production of good requirements. Equipment and components with comprehensive properties (corrosion resistance and formability). 301 stainless steel exhibits obvious work hardening phenomenon during deformation, and is used in various occasions requiring higher strength. 302 stainless steel is essentially a variant of 304 stainless steel with higher carbon content, which can obtain higher strength by cold rolling. 302B is a kind of stainless steel with high silicon content, which has high resistance to high temperature oxidation. 303 and 303Se are free-cutting stainless steels containing sulfur and selenium, respectively, and are used in applications where free-cutting and high surface finish are mainly required. 303Se stainless steel is also used to make parts that require hot upsetting, because under these conditions, this stainless steel has good hot workability. 304L is a lower carbon variant of 304 stainless steel used where welding is required. The lower carbon content minimizes carbide precipitation in the heat-affected zone near the weld, which can lead to intergranular corrosion (weld erosion) of stainless steel in some environments. 304N is a nitrogen-containing stainless steel, and nitrogen is added to increase the strength of the steel. 316 (18Cr-12Ni-2.5Mo) material: due to the addition of Mo, its corrosion resistance, atmospheric corrosion resistance and high temperature strength are particularly good, and can be used under harsh conditions; excellent work hardening (non-magnetic).
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: full threaded lead screw, white zinc spring washer, custom nuts, Q524 pins and other products, we can provide you with suitable fasteners for you solution.
