Service HotlineWhen the mold is manufactured, many positioning pins need to be installed to fix the relative position between the two parts. The positioning pins are usually sunk into the positioning pin holes on the mold. Since the mold needs to be pulled out frequently during assembly, in order to Remove the parts and make corrections. At the same time, the mold also needs to pull out the positioning pins during maintenance to remove the damaged parts for maintenance. Therefore, the workload of pulling the pins is large. The existing methods are: 1) When installing the pins, The operator uses a self-made long screw that matches the threaded hole of the pin to screw it into the pin, and then aligns the pin hole with a hammer to hit the screw to make the pin snap in, and then screw the screw out by hand. The disadvantage is: on the one hand, the hammer hits the screw It is easy to cause the screw to be damaged or deformed, and it cannot be used normally. On the other hand, it is labor-intensive to remove the screw by hand and may not be able to be removed; 2) When pulling out the pin, the operator will screw the screw into the pin and use force directly or with pliers To pull out a screw, a few companies use a large pin puller to pull it out. The disadvantage is that it is too laborious and time-consuming to pull out by hand or with pliers. Even if a large pin puller is used, the weight of the pin puller itself is large. , it is inconvenient to use.
Stud bolts generally need to be surface treated. There are many types of bolt surface treatments. Generally, electroplating, blackening, oxidation, phosphating, and electroless zinc flake coating are commonly used. However, electroplated fasteners account for a large proportion of the actual use of fasteners. Especially in automobiles, tractors, home appliances, instrumentation, aerospace, communications and other industries and fields are more widely used. However, for threaded fasteners, not only a certain anti-corrosion capability is required in use, but also the interchangeability of threads must be ensured, which can also be called screwability here. In order to meet the dual-use performance of anti-corrosion and interchangeability required by threaded fasteners in use, it is very necessary to formulate special plating standards. [1] The GB/T5267.1-2002 [Threaded Fastener Electroplating Coating] standard is one of the national standards Fastener Surface Treatment series of standards, which include: GB/T5267.1-2002 [Fastener Electroplating Layer]; GB/T5267.2-2002 [Fastener electroless zinc flake coating] two standards. This standard is equivalent to the international standard ISO4042; 1999 [Threaded fastener electroplating layer]. This standard replaces the GB/T5267-1985 [Threaded Fastener Electroplating Coating] standard.
Guangdong Yueluo Hardware Industry Co., Ltd. was founded in 1998, and the factory was established in Feilong Industrial Zone, Xiaolan Town, Zhongshan City, Guangdong Province, with an investment of 10 million yuan. The main production is a variety of national standard, non-standard, British, American, metric screws. Mainly include: special screws for the electronics industry (machine screws, self-tapping screws, special screws): nuts (general nuts, flange nuts, external teeth nuts): Washers (external teeth, internal teeth, flat springs) Gaskets, etc.); lathes (precision automatic lathe parts, connecting parts, embedded parts, fasteners, decorative parts, etc.).
The nut is based on the reaction force principle of the inner hexagonal cone of the clamping part and the outer hexagonal cone of the locking part. The higher the pressure, the tighter the lock, so that the bolt can achieve the purpose of self-locking and tightening. The existing bolts rely on multiple nuts against each other to prevent loosening. This method cannot be completely locked, and the bolts are easily loosened when subjected to huge pressure and vibration, which hides potential safety hazards;
At present, there are many kinds of smart terminals on the market. Due to the reduction of the overall volume of the smart terminal and the more compact internal parts, the nuts are generally made of injection-molded nuts. The traditional injection-molded nuts are directly fixed on the equipment. During the process, it is easy to loosen and fall off, which greatly reduces the service life of the injection nut and brings inconvenience to the use of the mobile terminal.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: self-locking nuts, flat head copper column nuts, special-shaped bolts, pins and other products, we can provide you with suitable products for you. Fastener Solutions.
