Service HotlineRivet nuts are mostly used in some chassis cabinets, square tubes and round tubes, fan production, equipment production, and zinc steel guardrails. Next, let’s talk about rivet nuts. The rivet nuts are also used on the top of the chassis cabinet sheet to provide threads. Its mode of operation is to use a riveting machine for riveting. In this case, the requirements will be higher, and a riveting machine is required. After the pressure riveting nut is riveted to the upper side of the sheet, it is very flat and will not have protrusions. Pressure riveting nuts are mainly used in the production of some chassis and cabinets, as well as some equipment production, water pumps, automobiles, and other production enterprises.
In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35, and the screws enter the screw accommodating hole 39 from the discharge port through the guide rail 6. The slotting is carried out, which improves the efficiency and saves the labor cost.
The quality of the combination screw should start with the screw wire of the combination screw manufacturer. The wire of the screw is the first hurdle to determine the quality of the combination screw. Even if the wire is not good, even if the production equipment is advanced and the staff is skilled, it is impossible to produce high-quality combination screws. In the second look at the quality of the combination screw products, from the overall aesthetics of the combination screw. A combined screw is formed, the size of the screw head, the superior appearance of the flat washer, whether the screw thread can pass the stop gauge, etc. These are all things that need to be detected. A good combination screw, its overall standard can meet the national standard requirements, or customer requirements. Finally, the quality of the combination screw product is seen from the color of the plating. Of course, the iron combination screw needs to be plated, but the stainless steel combination screw does not need it. Some of them are passivation at most, in order to increase the salt spray resistance of stainless steel combination screws. In the electroplating color of the combination screw, some of them are not well controlled, which will produce a great color difference. That doesn't look good.
In each maintenance, the newly replaced stud bolts and other accessories should be inspected. During the inspection, the focus should be on the head and guide part of the stud bolt. It is also necessary to strictly check that each part of the thread has No cracks or dents, also check the tooth shape of the studs for changes. Is there any abnormality in the thread pitch? If there is any abnormality, it must not be used again. A torque wrench should be used when installing the connecting rod cover. It must be tightened according to the specified standards, the torque should not be too large or too small, and attention should be paid to selecting the stud bolts and studs of the supporting manufacturer.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of quality also contributes to the improvement of the lifespan of the 12-year-old utensils.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: ASMEB18.2.2, blind hole through nuts, JISB1166 bolts, black 8.8 high-strength hexagonal nuts and other products, we can provide you with suitable tightening Firmware Solutions.
