Service HotlineYueluo Company adopts the following technical solutions: fasteners for preventing nuts from falling off, including bolts and nuts, the nuts are provided with screw holes, the screw holes are provided with internal threads, the bolts are provided with M grooves along its axial direction, M ≥1; There is an arc-shaped notch on the screw hole of the nut, and there are N V-shaped tooth grooves along the axial direction of the nut in the arc-shaped notch, N≥2; a locking strip is placed in the groove, and the locking The bar includes a locking bar body and a V-shaped locking tooth, the width of the locking bar body is the same as the width of the groove, the V-shaped locking tooth is located on one side of the locking bar body, and the V-shaped locking tooth is engaged with the V-shaped locking tooth.
The material of the rubber gasket is NBR nitrile rubber, which is the most commonly used and has the highest cost performance. The use of FFKM perfluoroelastomer gaskets is generally in the more advanced fields, such as the field of aerospace rockets. Because its price is quite expensive, but its performance is excellent and can exceed many metal materials. For specific material information, please refer to the following: Material Name Chemical Description English Abbreviation English Alias Nitrile Butadiene Rubber Acrylonitrile-Butadiene Rubber Ethylene-Propylene-Diene Rubber EPDM EP,EPT,EPR Neoprene Neoprene CR Neoprene Silicone Silicone Rubber WMQ PVMQ Fluorosilicone Fluorosilicone Rubber FVMQ FVMQ Acrylate Acrylate Rubber ACM ACM Ethylene Acrylate Vinyl -Acrylic Rubber AEM Vamac Styrene-Butadiene Styrene-Butadiene Rubber SBR SBR Polyurethane Polyester/Polyether Urethane AU/Eu AU/EU Natural Rubber Natural Rubber NR NR
With the rapid development of electronic technology, the integration of circuit boards is getting higher and higher, and the number of layers of circuit boards is increasing. Press-fit and fix to ensure accurate alignment during riveting and pressing. The rivets used on PCB boards are basically brass rivets. When riveting and pressing multi-layer PCB boards, metal chips are prone to appear, inner layer short circuits or foreign objects between layers, and because of the brass rivets With higher hardness and larger wall thickness, the riveted area of the PCB is thicker than the non-riveted area, which is easy to cause damage to the middle steel plate of the auxiliary tool. At the same time, the protruding rivets hinder the free expansion of the copper foil, which is easy to produce copper foil. wrinkling phenomenon. Now there are improved plastic rivets used to manufacture multi-layer PCB boards. The advantage is that no metal debris is generated, and at the same time, the tool steel plate is not damaged to the greatest extent. However, the existing plastic rivets are insufficient due to the inherent strength of plastics. When the PCB board is riveted and pressed, it is easy to deform, and the positioning is inaccurate, resulting in dislocation between layers, resulting in poor improvement of the product defect rate.
lead screw nut is provided with a through hole in the center for the screw rod to pass through, the surface of the through hole is provided with a screw thread engaged with the thread on the outer surface of the screw rod, and the surface of the through hole of the lead screw nut is provided with a thread along the surface of the through hole. The oil storage groove in the axial direction, the depth of the oil storage groove is greater than the depth of the thread.
The circlip extrusion and positioning mechanism includes a vertically installed circlip sleeve rod and a linear module controlled by a positioning motor; a plurality of circlips to be installed are sleeved on the surface of the circlip sleeve rod; the surface of the linear module can be Mobile installation quick clamp; the clamping mouth of the quick clamp is a tight top plate; the tight top plate is in contact with the upper circlip and moves up and down with the up and down movement of the circlip sleeve;
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: metal mesons, hand-twisted and hand-tightened adjustment bolts, T-block and t-slot pressure plate nuts, tie-rod fuselage aluminum rod internal teeth nuts and other products, We can provide you with the right fastener solution for you.
