Service HotlineGuangdong Yueluo Hardware Industry Co., Ltd. has upgraded and combined the fastening nut and the hexagonal nut to ensure the original function of the nut. The nut can be easily and safely disassembled by preparing practical small parts. The inner diameter of the lock ring is 0.1mm larger than that of the hexagonal nut, which is convenient for installation.
shaft card assembling device, comprising two struts, the same fixing plate is welded on the side of the two struts that are close to each other, the top of the fixing plate is symmetrically fixed with a motor, and the output shafts of the two motors are welded with * a bevel gear;
A double-nut self-locking fastener includes bolts, nuts, nuts, and elastic gaskets that can produce plastic deformation under pressure; the nut and the bolt are connected by threads, and one end of the nut is provided with an external thread; There is an inner thread in one end, and the inner thread of the nut and the outer thread of the nut constitute a thread pair; the other end of the nut is provided with a through hole, and the bolt passes through the through hole of the nut; when the nut and the nut are installed and tightened, the elastic gasket is located in the nut. between the bolt and the nut; a notch for cutting off the thread is arranged on the circumference of the bolt thread; the direction of the notch is parallel to the axial direction of the bolt.
In terms of inner hexagon, there are two versions of the national standard, one is GB70-76, the 76-year version, and the other is GB70-85, the 85-year version, most of which implement the DIN912 standard, so you should pay attention to the difference in actual business operations: GB70 -85 completely coincides with DIN912, so there is no difference in the use of the new standard, mainly the difference between GB70-76 and DIN912: for M8 series hexagonal products, the diameter of the round head of GB70-76 is 12.5MM, It is smaller than 13.27MM of DIN912. For M10 series inner hexagon products, the round head diameter of GB70-76 is 15MM, which is smaller than 16.27 of DIN912. For M12 series inner hexagon, the round head diameter of GB70-76 is 18MM. It is smaller than the opposite side 18.27 of DIN912, and the round head diameter of the inner hexagon GB70-76 of M16 and M20 series is 0.33MM smaller than that of DIN912, which are 24MM and 30MM respectively. DIN912 is 24.33MM and 30.33MM respectively. In addition, the width of the inner hexagon between the old standard and the German standard is different due to different standards. The inner side of GB70-76 is smaller, and it should be paid attention to in business operations.
At present, the standard parts on the market mainly include carbon steel, stainless steel and copper. A carbon steel. We distinguish low carbon steel, medium carbon steel and high carbon steel and alloy steel by the content of carbon in carbon steel material. 1 Low carbon steel C%≤0.25% is usually called A3 steel in China. Foreign countries are basically called 1008, 1015, 1018, 1022, etc. Mainly used for grade 4.8 bolts, grade 4 nuts, small screws and other products without hardness requirements. (Note: 1022 material is mainly used for drill tail screws.) 2 Medium carbon steel 0.25% 3 High carbon steel C%>0.45%. 4 Alloy steel is basically not used in the market: alloying elements are added to ordinary carbon steel to increase some special properties of steel: such as 35, 40 chromium molybdenum, SCM435, 10B38. Fangsheng screws mainly use SCM435 chromium molybdenum alloy steel, the main components are C, Si, Mn, P, S, Cr, Mo. Two stainless steel. Performance grade: 45, 50, 60, 70, 80 1 Mainly divided into austenite (18% Cr, 8% Ni) with good heat resistance, good corrosion resistance and good weldability. A1, A2, A4 2 Martensite, 13%Cr have poor corrosion resistance, high strength and good wear resistance. C1, C2, C4 ferritic stainless steels. 18%Cr has better upsetting and corrosion resistance than martensite. The imported materials on the market are mainly Japan. According to the level, it is mainly divided into SUS302, SUS304 and SUS316. Three coppers. Commonly used materials are brass...zinc-copper alloys. The market mainly uses H62, H65, H68 copper as standard parts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: corrosion-resistant screws, extended bolts for accessories sets, cross-head three-combination screws and nuts, hexagon single-head studs and other products, we can provide you with Provide the right fastener solution for you.
