Service HotlineCommonly used standards are broadcast. For hexagonal nuts, the commonly used standards are: GB52, GB6170, GB6172 and DIN934. The main differences between them are: the thickness of GB6170 is thicker than that of GB52, GB6172 and DIN934, commonly known as thick screw cap. The other is the difference between the opposite sides, the opposite sides of DIN934, GB6170 and GB6172 in the M8 nut series are 13MM smaller than the opposite side 14MM of GB52, and the opposite sides of M10 nuts, DIN934 and GB52 are 17MM. The opposite side of GB6170 and GB6172 should be 1MM larger, M12 nut, DIN934, GB52's opposite side is 19MM larger than GB6170 and GB6172's opposite side 18MM is 1MM larger. For M14 nuts, the opposite side of DIN934 and GB52 is 22MM, which is 1MM larger than the opposite side of GB6170 and GB6172, which is 21MM. The other is the M22 nut. The opposite side of DIN934 and GB52 is 32MM, which is 2MM smaller than the opposite side of GB6170 and GB6172, which is 34MM. (Besides the thickness of GB6170 and GB6172 are the same, the width of the opposite side is exactly the same) The rest of the specifications can be used in general without considering the thickness.
lead screw nut is provided with a through hole in the center for the screw rod to pass through, the surface of the through hole is provided with a screw thread engaged with the thread on the outer surface of the screw rod, and the surface of the through hole of the lead screw nut is provided with a thread along the surface of the through hole. The oil storage groove in the axial direction, the depth of the oil storage groove is greater than the depth of the thread.
Fasteners are a type of mechanical parts that are used for fastening connections and are widely used. Fasteners are used in a wide range of industries, including energy, electronics, electrical appliances, machinery, chemicals, metallurgy, molds, hydraulics, etc., in various machinery, equipment, vehicles, ships, railways, bridges, buildings, structures, tools, instruments, etc. , chemical industry, instruments and supplies, etc., all kinds of fasteners can be seen, which are the most widely used mechanical basic parts. It is characterized by a wide variety of specifications, different performance uses, and a very high degree of standardization, serialization and generalization. Therefore, some people also refer to a type of fasteners with existing national standards as standard fasteners, or simply as standard parts.
When the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
1. No matter what industry it is, the business is more difficult, and it is still more difficult for the fastener business. After a long period of contact, I realized that the business of making fasteners also requires a lot of attention to be able to do it well. In the business of making fasteners, not just any person can do it, and they all have certain requirements. 2. When it comes to the business of fasteners, no matter what kind of salesperson, the first thing you must have is enough patience, so that we can do this job with confidence, and some customers are not difficult to follow us. Communication, as long as we have enough patience, then we have a greater chance of being able to cooperate with customers on fasteners, and in the face of some relatively large fastener customers, sometimes it is not that we can get it all at once , Sometimes if you want to cooperate, you need to go through multiple contacts to promote a cooperation, so as a salesperson, enough patience is essential. 3. Then, as a fastener salesman, what you need to have is perseverance. Sometimes the salesperson is difficult at work. At this time, you need to adjust it in time, so it will not lead to the phenomenon of giving up easily, after all As a salesman, only through our own efforts can we have the opportunity to receive orders for fasteners from customers. What we need is to be able to face difficulties and move forward bravely. 4. The most important thing for fastener salesmen is to pay attention to details. If we can do a good job in the details, then sometimes we are not far from success. The above are several requirements that need to be met in the fastener business.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hand percussion rivets, red copper countersunk head rivets, expansion ring screws, GB6172DIN439 outer hexagon thin nuts, square nuts and other products, we can provide You have the right fastener solution for you.
