your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Processing mirror universal joint long and short connecting rod sliding rod L-shaped bending rod manual sleeve connecting rod connection

author:[email protected] Click:7842end source: time:2024-01-06 19:07:35

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: full-tooth high-stren...

At present, injection molding screws are widely used in various electronic and automotive components, including a body, the middle of which is provided with a through hole 3, the body head 1 has a hexagonal cross-section, and the tail 2 is provided with screw teeth. When in use, the middle through hole 3 of the main body will first put the wire harness, and then fix it by injection molding from the head I, and the threads of the tail 11 should be connected and installed with other components. Because the head I of the main body is hexagonal, the torque provided after injection molding is insufficient. Therefore, after the external thread is installed and connected with other components, the head is prone to slip, the installation is not reliable, and there is no push-pull force, resulting in product failure and increased safety hazards.

Heat resistance refers to both the oxidation resistance or gas medium corrosion resistance at high temperature, that is, thermal stability, and at the same time, it has sufficient strength at high temperature, that is, thermal strength. As the material requirements of products produced by customers are getting higher and higher, the requirements for screws used in product materials are also getting higher and higher. When product materials face harsh environments and special occasions, more and more high-quality mechanical properties of stainless steel screws are used. Therefore, stainless steel screws were selected. The requirements are getting higher and higher, and the material of stainless steel screws is getting higher and higher. Therefore, many ordinary stainless steel screws SUS201 are replaced by stainless steel SUS304 screws and stainless steel screws SUS316. Of course, if some requirements are not so high, general customers will choose stainless steel screws SUS201, which are relatively cheap in cost.

The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (10), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the deformation. effect.

When using, after installing the nut and the bolt in place, insert the locking strip from the groove of the bolt, and make the V-shaped locking teeth of the locking strip snap into one of the V-shaped tooth grooves, and push the locking strip into the groove as a whole. The V-shaped locking teeth are stuck in the nut, and the locking strip body is stuck in the groove of the bolt, thereby restricting the relative rotation of the nut and the bolt, and there are threads between the nut and the bolt to restrict their relative sliding, so it can prevent the nut from loosening, even from The bolt falls off; when the nut needs to be disassembled, it is only necessary to pull out the locking strip from the groove, and the nut can be disassembled normally.

Generally known bolts refer to screws with a larger diameter. According to this statement, the diameter of screws is much smaller than that of bolts. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: national standard positioning screws, black high-strength nuts, king eight lock washers, wholesale stainless steel and other products, we can provide you with suitable fasteners for you piece solution.

long and short post

Machined mirror gimbal


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].