Service HotlineIn view of the deficiencies of the prior art, a simple structure is provided, which can ensure that the nut body and the washer are assembled together during the production of the wheel nut, and will not be separated from each other in any occasion, so as to ensure the reliability of the assembly, and the nut will no longer appear. The wheel nut assembly that needs to be reassembled after use or placement saves time and effectively improves the convenience of the wheel nut when it is used or placed
For achieving the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solutions: a pin, comprising a pin cap and a described pin rod, the pin cap and one end of the pin rod are fixedly connected, and the pin rod There is a convex body, the convex body is fixedly connected with the pin rod, the convex body is located on the pin rod rod body, and the other end of the pin rod is provided with a top connecting body, and the top connecting body is fixedly connected with the pin rod , the top contact body includes several top contact units and discs, each top contact unit is coaxially arranged with the pin rod, the top contact units are sequentially fixedly connected along the axis direction of the pin, the top contact unit is The major diameter of the outer contour of the connecting body is larger than the diameter of the pin rod.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
The machinery industry is one of the main users of fasteners. Due to China's late understanding of the important position of mechanical basic parts in the machinery industry and a long-term lack of investment, the entire industry has a poor foundation, weak foundation and weak strength. Especially with the improvement of the level of the main engine in China, the bottleneck phenomenon that the mechanical basic parts lag behind the main engine has become increasingly apparent. Today, although the state has given certain support in technology introduction, technological transformation, scientific research and development, etc., there is still a big gap compared with the current market demand and foreign levels. Unstable quality, high early failure rate and poor reliability. Fasteners are the main basic products in the machinery industry, and the development of the machinery industry also puts forward higher requirements for fastener products. Domestic ordinary standard fasteners have always been in oversupply, while high-end fasteners (high temperature, special-shaped, titanium-plastic composite, special performance and other fasteners) are in short supply, and they also rely on imports. The State Machinery Bureau lists ordinary standard fasteners as restricted development products, and high-strength special-shaped fasteners as currently encouraged development products. With the improvement of the country's industrialization level and technological progress, the use of high-strength fasteners has gradually increased.
Bolt: A mechanical part, a cylindrical threaded fastener with a nut. A type of fastener consisting of a head and a screw (a cylinder with an external thread), which needs to be matched with a nut to fasten and connect two parts with through holes. This form of connection is called a bolted connection. If the nut is unscrewed from the bolt, the two parts can be separated, so the bolt connection is a detachable connection.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: non-standard machining parts bolts, half pan head screws, cap nuts and nuts, pressure riveting pressure plate nuts and other products, we can provide you with suitable products for you. Fastener Solutions.
