Service HotlineIn view of the above problems, Guangdong Yueluo Hardware Industry Co., Ltd. aims to provide a new type of open blind rivet suitable for riveting of aluminum, steel and stainless steel sheets with foamed materials.
In order to solve the problems existing in the prior art, Yueluo Company provides a fastener that prevents the nut from falling off. After the nut is installed in place, a locking strip can be inserted into the groove of the bolt to lock the nut, so that the nut can be locked. It cannot be loosened to prevent the nut from falling off. If the nut needs to be removed, the nut can be removed normally after removing the locking strip.
NPT, PT, G are all pipe threads. NPT is the abbreviation of National (American) Pipe Thread, which belongs to the American standard 60-degree taper pipe thread, which is used in North America. National standards can be found in GB/T12716-1991 PT is the abbreviation of Pipe Thread, which is a 55-degree sealed conical pipe thread, which belongs to the Whitworth thread family and is mostly used in Europe and the Commonwealth of Nations. Commonly used in water and gas pipe industry, the taper is specified as 1:16. The national standard can be found in GB/T7306-2000 G is a 55 degree non-threaded sealing pipe thread, which belongs to the Whitworth thread family. Marked as G stands for cylindrical thread. National standards can be found in GB/T7307-2001 In addition, the 1/4, 1/2, 1/8 marks in the thread refer to the diameter of the pipe, and the unit is inches. People in the industry usually refer to thread size in points, 1 inch equals 8 points, 1/4 inch is 2 points, and so on. G seems to be the general name for pipe threads (Guan), and the division of 55 and 60 degrees is functional, commonly known as pipe circle. That is, the thread is machined from a cylindrical surface. ZG is commonly known as pipe cone, that is, the thread is made of a conical surface. The general water pipe joints are like this. Rc means conical internal thread ZG means taper pipe thread, 3/4 means inch mark, which is 3/4 inch conical pipe Thread, there is in the Hardware Manual. The national standard stipulates that the major diameter of ZG 3/4 thread is 26.44 mm. Please refer to Metric, American and British Thread Standard Manual (Third Edition). Its representation method should be: ZG 3 /4″. Among them (〃) is the representative symbol for inches. One inch is equal to 8 inches. The origin of 3/4 is 6/8=3/4. Commonly known as 6 points. Similarly, the major diameter of ZG 1/2″ thread≈21 mm. Commonly known as 4 points. ZG 1″ thread diameter ≈ 33 mm. Commonly known as 1 inch. ZG 1 1/2″ thread pipe outer diameter ≈ 48 mm. Commonly known as 1 inch and a half. Taper pipe thread is very similar to pipe thread, the difference is Only in the taper. Note that the basic size of the pipe thread and ordinary thread is different. DN is the nominal diameter
The utility model relates to a connecting piece, in particular to a female and female screw used for shaping products in interior decoration. In the current decoration project, when fixing the decoration stereotyped product, the process is complicated, so labor-intensive and time-consuming, the construction cost is high, and the construction degree is low. For example, the decorative board for fixing the wall, the main process step used in its operation is the leveling of the nail strip. That is to say, saw the wood to the required specifications, then draw horizontal and vertical lines on the wall, and then nail the wooden strips to the wall according to the horizontal and vertical lines, and then glue and glue the board. The first step is to install the lines, color and paint. It can be seen that it is quite troublesome to use the above method to construct. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a female screw, which can skillfully connect decorative products to the wall. As conceived above, the technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is a female screw, which is characterized in that both ends of the screw are threaded, the screw-in end is screwed into the plastic expansion tube inserted into the wall, and the other end of the screw is threaded with the same A female piece is mated and connected. The other end of the screw can also be barb-shaped and directly fit with the decorative board. The screw thread of the screw-in end is a wood thread, and the thread of the mating connection end with the female part is a machine thread.
However, Yueluo still feels that there should be room for improvement for the screw improvement and screw that integrates stability, labor, fast and multi-function in the above two cases; for example, No. 556784 screw improvement Although the rod has the function of cutting and collecting chips, when the screw starts to screw into the object such as wood, it is hindered by the hardness of the object's tissue, so the staff still needs to exert considerable force, resulting in the lock. In the solid operation, there is still a lack of difficulty in screwing in operation; another example, new cases such as No. 289410 screw that integrates locking, stability, labor, fast and multi-function, although the rod has the structural function of cutting and chip removal, it is The rod part is screwed into the middle section to the rear section of the object. Since the debris cannot be discharged, the rod part pushes the outer part of the object to the surrounding tissue of the object, so that the object expands outwards and even seriously damages the appearance of the object.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: long hexagon socket screws, torx countersunk head screws, buttonhole copper flat head rivets, wholesale hexagon nut screws and other products, we can provide you with suitable products for you fastener solutions.
