Service HotlineMany parts on the car need to be rubberized, which can reduce noise, especially the parts related to shock absorption. Nuts are welded on many of these parts to facilitate the installation of other parts on them. The sheet metal is generally relatively thin, and most of them are only one or two millimeters. A through hole is punched, and then the nut is placed in the hole, and then around it. Spot welding is done so that it can be fixed. After spot welding, the periphery of the screw hole on the sheet metal will not be flat due to thermal deformation, which will affect the appearance.
In general, the electroplating of combination screws generally refers to the de-plating of iron combination screws. Electroplating is divided into environmental protection and non-environmental protection. Commonly used combination screw electroplating colors include green color zinc, green blue zinc, green white zinc, green nickel, red color, white zinc, white nickel, etc. Cross recessed combination screws, hexagonal combination bolts and self-tapping combination screws are used in the same way as the corresponding cross recessed screws, hexagon head bolts and self-tapping screws. The main feature of these combination screws is that they are equipped with corresponding washers, which are very convenient to use.
Stainless steel screws usually refer to steel screws that are resistant to corrosion by air, water, acids, alkali salts or other media. Stainless steel screws are generally not easy to rust and durable, and can be used in environmental protection equipment, medical equipment, communication equipment and other fields.
Gaskets are widely used in the machinery industry. According to the different needs of machinery and equipment in different industries, the structural forms of the sealing points are also different. Plum washer is one of the commonly used seals. It is commonly used between the pump and the motor coupling. In the actual production process of the enterprise, it is found that due to the influence of the material and structure, this type of gasket in common use can withstand impact force. Small, the septum is easily damaged. Because the current plum washers are all one-piece structures, even if one or several of the partitions are damaged, they need to be replaced as a whole. Although the value of a single plum washer is low, it needs to be shut down for maintenance and replacement almost every week. It also seriously affects the normal production of the enterprise, and the one-piece plum blossom gasket is also difficult to repair, adding unnecessary use costs to the enterprise. For this reason, the plum blossom gasket needs to be improved to strengthen the impact resistance of the gasket, and can be repeated Maintenance and use, prolong the maintenance cycle of the equipment, and ensure the normal production of the enterprise. The purpose of the utility model Yueluo is to solve the above-mentioned deficiencies in the existing technology, improve the existing technology, and provide a simple structure, which strengthens the impact resistance of the gasket, and can be repeatedly maintained and used to prolong the maintenance of the equipment. The cycle guarantees the plum blossom elastic washer normally produced by the enterprise. In order to achieve the above purpose, Yueluo is achieved through the following technical solutions-namely a plum blossom elastic washer, including an elastic washer body with a partition, the technical point is that the washer body is composed of a washer base and a partition that is independent of each other. , the septum and the gasket base are fixedly connected into one through the fixing piece. In order to further strengthen the impact resistance of Yueluo, the contact parts of the spacer and the washer base are respectively processed with a limited clamping table and a matching groove, so that the spacer and the washer base can be better integrated into one. According to the different specifications of the torx washer, the spacer and the washer can be fixed as a whole by rivets; or by screws. In addition, a semi-rigid tightening ring with grooves is embedded inside the washer base, and the width of the tightening ring is smaller than the width of the washer base; the ends of the rivets or screws are located in the grooves of the tightening ring, so as not to affect the performance of the torx washer JH is often installed. After the above improvement, Yueluo has improved the one-piece structure of the plum-blossom washer into a split structure and adopted a variety of fixed structure forms, so it has a simple structure, strengthens the impact resistance of the gasket, and can be repeatedly maintained and used. , Extend the maintenance cycle of the equipment and ensure the advantages of the normal production of the enterprise.
Common types of common screws All kinds of common screws (20 pieces) a. Slotted: a word ( Minus ) b. Phillips: cross ( Plus ) c. Phil-Slot: a word / cross d. Hex Socket: hexagon socket e. One Way: One-way (can only be locked in, not out) A-4: Head Code/ head shape. a. Flat: Flat head (after locking, the top is flush with the work piece) b. Oval: salad head, O head, countersunk head screw unit of measure screw unit of measurec. Round: round headd. Pan: round flat heade. Truss: large round flat headf. Hex: hexagon head. A-5: Finish Code/Appearance treatment. Metric Self-tapping screw: Mark Tapping Type directly behind the product name. Ex: M3 x 6 –PPB, Tapping Type: M3 self-tapping screw, 6mm long, cross, round flat head, black plated. Generally, it is determined by product type or mark. For Sheet Metal or plastic parts. *Pitch = Threads per inch
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: shaft pin toy city connecting rod locks, metal self-locking nuts, screw screw connecting nuts, cross recessed mushroom head screws and other products, we can provide you with Provide the right fastener solution for you.
