Service HotlineFurther, it also includes a motor, the motor is provided with a thruster that makes the cutting wheel move towards the conveying device, the other end of the motor is provided with a bearing, the output end of the motor is provided with a special-shaped wheel, the special-shaped wheel is toothed with the bearing, and the motor drives the special-shaped wheel to rotate. , move the cut-off wheel closer to or away from the conveyor.
When the countersunk head screws and hexagon socket head bolts are produced by the cold heading process, the original structure of the steel will directly affect the forming ability of the cold heading process. In the process of cold heading, the plastic deformation of the local area can reach 60%-80%, so the steel must have good plasticity. When the chemical composition of the steel is constant, the metallographic structure is the key factor to determine the plasticity. It is generally believed that the coarse flaky pearlite is not conducive to cold heading forming, while the fine spherical pearlite can significantly improve the plastic deformation ability of the steel. For medium carbon steel and medium carbon alloy steel with a large amount of high-strength bolts, spheroidizing (softening) annealing is performed before cold heading, so as to obtain uniform and fine spheroidized pearlite to better meet the actual production needs. For the softening annealing of medium carbon steel wire rods, the heating temperature should be kept above and below the critical point of the steel, and the heating temperature should not be too high, otherwise tertiary cementite will precipitate along the grain boundary, resulting in cold heading cracking. The wire rod of medium carbon alloy steel is annealed by isothermal spheroidization. After heating at AC1+ (20-30%), the furnace is cooled to slightly lower than Ar1, the temperature is about 700 degrees Celsius for an isothermal period, and then the furnace is cooled to about 500 degrees Celsius and air-cooled. The metallographic structure of the steel changes from coarse to fine, from flake to spherical, and the cracking rate of cold heading will be greatly reduced. The general area of softening annealing temperature for 35\45\ML35\SWRCH35K steel is 715-735 degrees Celsius; while the general heating temperature for spheroidizing annealing of SCM435\40Cr\SCR435 steel is 740-770 degrees Celsius, and the isothermal temperature is 680-700 degrees Celsius.
The existing way to achieve radial locking of the shaft is generally to sleeve the positioning block on the shaft, and then use a cylindrical pin to pass through the positioning block to lock the shaft. The locking structure and method are as follows: A locking groove with an arc-shaped cross-section is set on the outer side of the shaft along the direction perpendicular to the axis of the shaft, an opening is set on the positioning block, and then a cylindrical pin is used to pass through the positioning block from the outside of the positioning block and screw the lock at one end of the cylindrical pin. When the lock nut is tightened, the opening on the positioning block will be deformed inwardly and locked on the shaft.
A crank press with bilateral transmission, such as a briquettes machine, requires 1. The rotation phase of the main shaft gears on both sides must be consistent; 2. The connection between the main shaft and the main shaft gear should be free of gaps. In order to meet this requirement, there are mainly two schemes for the connection between the main shaft and the main shaft gear. Option 1, one or both ends of the main shaft and the main shaft gear are connected by flat keys. This scheme requires that the matching clearance between the main shaft and the gear hub is small, so it is difficult to process, assemble and maintain; Option 2, one or both ends of the main shaft and the main shaft gear Using taper-sleeve connection, this solution has good performance, but high cost and poor rigidity
The spring screw is a tool that uses the physical and mathematical principles of the oblique circular rotation of the object and the frictional force to fasten the machine parts step by step; the screw is a common invention in people's production and life for thousands of years. According to the application field, Screws have a wide range of applications.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: set bolts and extended screws, flat washers and spring washers combination sets, aluminum alloy column connections, Kimi bolts and other products, we can provide you with products suitable for you fastener solutions.
