Service HotlineThe beneficial effects of Guangdong Yueluo Hardware Industry Co., Ltd. are: the chip nut provided by Guangdong Yueluo Hardware Industry Co., Ltd. has a circle of serrated teeth protruding outward on the edge of the welding end face. During welding, excess solder After overflowing, it flows into the peripheral serrated convex tooth gap. In this way, on the one hand, the solder on the welding end face can be made uniform, and the welded chip nut can be neat and beautiful. On the other hand, the overflowed solder is combined with the serrated convex tooth gap. The welding area is increased, and the firmness and reliability of the welding are improved.
An asphalt pavement screw, the asphalt pavement screw includes a main rod, an outer jacket, a pressing piece and a nut, the main rod is a columnar rod, the lower end of the main rod is provided with a table for supporting the outer jacket, and the middle part of the main rod passes through the outer jacket The upper part of the main rod is provided with a threaded section, the pressing piece and the nut are set on the threaded section, and at least two deformation holes are provided on the outer sleeve, and the middle part of the deformation hole is larger than the upper and lower sides of the deformation hole, The part between the adjacent deformation holes is the deformation part, and the width of the middle part of the deformation part is smaller than the width of the upper and lower sides of the deformation part. After the asphalt pavement screw of Guangdong Yueluo Hardware Industry Co., Ltd. is assembled, it has strong bonding force with the asphalt road. Even if it is hit, it will not be separated from the asphalt road. Using this asphalt pavement screw to fix the road railing can strengthen the road railing. The firmness of the assembly.
In the automobile industry, it is often necessary to install bolts at the opening of a closed cavity to fix and connect other parts. However, the diameter of the opening of the closed cavity is often larger than that of the head of the bolt, so it is necessary to set a strip-shaped spacer on the head of the bolt, so that the spacer can penetrate the opening longitudinally, and then block the opening horizontally, so as to be stuck with an upside-down buckle. Bolt head. However, since the bolt body of the bolt has a certain length, the manual vertical and horizontal turning operation after the strip spacer penetrates the opening is very difficult, and it is easy to drop the bolt and the spacer into the airtight cavity together, which greatly increases the assembly time. Increased labor costs.
When the mold is manufactured, many positioning pins need to be installed to fix the relative position between the two parts. The positioning pins are usually sunk into the positioning pin holes on the mold. Since the mold needs to be pulled out frequently during assembly, in order to Remove the parts and make corrections. At the same time, the mold also needs to pull out the positioning pins during maintenance to remove the damaged parts for maintenance. Therefore, the workload of pulling the pins is large. The existing methods are: 1) When installing the pins, The operator uses a self-made long screw that matches the threaded hole of the pin to screw it into the pin, and then aligns the pin hole with a hammer to hit the screw to make the pin snap in, and then screw the screw out by hand. The disadvantage is: on the one hand, the hammer hits the screw It is easy to cause the screw to be damaged or deformed, and it cannot be used normally. On the other hand, it is labor-intensive to remove the screw by hand and may not be able to be removed; 2) When pulling out the pin, the operator will screw the screw into the pin and use force directly or with pliers To pull out a screw, a few companies use a large pin puller to pull it out. The disadvantage is that it is too laborious and time-consuming to pull out by hand or with pliers. Even if a large pin puller is used, the weight of the pin puller itself is large. , it is inconvenient to use.
The side gear thrust washer used in the automobile differential is a flat washer, which is installed between the differential housing and the side gear to prevent the side gear from retreating. Due to the high-speed rotation of the side gear when the differential is working, it is necessary to ensure that the contact surfaces on both sides of the flat gasket are well lubricated.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: eyelet rivets, knurled copper column copper screws and nuts, flat washers set screws, hex bolts and screws and other products, we can provide you with suitable products for you. Fastener Solutions.
