What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
The utility model relates to a connecting piece, in particular to a female and female screw used for shaping products in interior decoration. In the current decoration project, when fixing the decoration stereotyped product, the process is complicated, so labor-intensive and time-consuming, the construction cost is high, and the construction degree is low. For example, the decorative board for fixing the wall, the main process step used in its operation is the leveling of the nail strip. That is to say, saw the wood to the required specifications, then draw horizontal and vertical lines on the wall, and then nail the wooden strips to the wall according to the horizontal and vertical lines, and then glue and glue the board. The first step is to install the lines, color and paint. It can be seen that it is quite troublesome to use the above method to construct. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a female screw, which can skillfully connect decorative products to the wall. As conceived above, the technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is a female screw, which is characterized in that both ends of the screw are threaded, the screw-in end is screwed into the plastic expansion tube inserted into the wall, and the other end of the screw is threaded with the same A female piece is mated and connected. The other end of the screw can also be barb-shaped and directly fit with the decorative board. The screw thread of the screw-in end is a wood thread, and the thread of the mating connection end with the female part is a machine thread.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
Fan rivets are specially designed for manual installation. They can be pulled in through the holes of the panel or the bottom frame. They are made of elastomer material with good toughness and can be installed quickly even in interference assembly. The design is clever and has elastic function. It is not easy to slide out after being pulled in with the corresponding aperture. The fan rivets are mainly used in the fixing of electronic computer case fans, heat sinks and chips, with anti-vibration and noise reduction.
The electroplating of cross recessed screws generally refers to the electroplating of iron cross recessed screws. Stainless steel cross recessed screws are rarely electroplated. The electroplating colors of cross recessed screws are divided into environmental protection and non-environmental protection. Environmental protection blue zinc, environmental protection color zinc, environmental protection black zinc, environmental protection white nickel, etc., non-environmental protection includes white nickel, white zinc, color zinc, black zinc, black nickel, black cladding, blue zinc.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
