What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
kind of screw provided by Yueluo, the rod body of the screw rod has a thread segment, one end of the thread segment is provided with an annular convex ring on the outer peripheral surface of the rod body, and the distance between the convex ring at the front end of the screw threading direction and the rod core Smaller than the nominal size of the threaded section or the distance from the rear end of the bead to the rod core in the screwing direction is greater than the nominal size of the threaded section.
Round head three-combination screws are also called pan-head three-combination screws, which are divided into large pan-head three-combination screws and small pan-head three-combination screws. The materials are divided into stainless steel and iron. The stainless steel round head three-combination screws include stainless steel small pan head three-combination screws and stainless steel large pan-head three-combination screws. The national standards are respectively expressed as GB9074.8 and GB9074.4.
kind of screw provided by Yueluo, the rod body of the screw rod has a thread segment, one end of the thread segment is provided with an annular convex ring on the outer peripheral surface of the rod body, and the distance between the convex ring at the front end of the screw threading direction and the rod core Smaller than the nominal size of the threaded section or the distance from the rear end of the bead to the rod core in the screwing direction is greater than the nominal size of the threaded section.
① Nominal thread outer diameter (thread specification): divided into metric system and inch system. Metric thread → common specifications are 2; 2.3; 2.5; 2.6; 2.9; 3; 3.1; 3.5; 4; 4.2; 4.5; The unit is mm (millimeters). Inch thread→ Common specifications are 2#;4#;6#;8#;10#;12#;1/4;7/32;5/16;3/8;1/2 ;9/16;3/ 4. The unit is in (inches). ② Number of teeth/pitch: Definition of number of teeth → the number of teeth lines in one inch (25.4mm) length. Pitch Definition → Distance value between two adjacent threads. Conversion of number of teeth and pitch of teeth → pitch of teeth = 1 inch/number of teeth ③Nominal length: divided into metric system and inch system. Metric Nominal Length → Common values are 5, 6, 6.5, 7, 8, 9, 9.5, 10, 11, 12, 13, 14, 15, 16, 18, 19, 20, 21, 25, 28, 30, 31 , 32, 35, 40, 42, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120. The unit is mm (millimeters). Imperial Nominal Length → Common values are 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, 1, 2, 3. Units: in (inches). ④Head type: use letters to indicate the type of head type, please refer to the previous classification of commonly used screw head types. ⑤Tooth type/tail type: Use letters to indicate the type of tooth type/tail type, please refer to the previous Commonly used screw thread/tail type classification. ⑥Groove type: Please refer to the previous section Category of common screw groove types of our company. Cross-slotted or non-slotted (such as punched hexagon head screws) do not need to be marked here, and other groove types need to be described in words. ⑦Special labeling: In general, no labeling is required. When expressing its characteristics, it is described in words at this position. For example: the specification name of the screw is described as 4-0.7x70PM±tooth length 35, which means 4 is the nominal diameter of the screw thread, 0.7 is the pitch, 70 is the nominal length of the screw, and P means its The head type is a pan head, M means its tooth type/tail type is a wire thread type, ± means its groove type is ± groove and can also be expressed by plus or minus groove. Tooth length 35 is special Mark, specify the thread length value of this screw.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
