What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
According to the properties of nuts, there are mainly national standard (GB), German standard (DIN), international standard (ISO), Japanese standard (JIS), American standard (ASTM/ANSI) and other standards. Among them, the national standard, German standard, and Japanese standard are represented by M (such as M8, M16), and the American system and the British system are represented by fractions or # (such as 8#, 10#, 1/4, 3/8). Commonly used national standard GB41 Ⅰ type hexagonal nut - C grade GB6170 Ⅰ type hexagonal nut - A, B grade GB6171 I type hexagonal nut - fine thread - A, B grade GB6172 hexagonal thin nut - A, B grade - chamfering GB6173 Hexagonal Thin Nut - Fine Thread - A, B Grade GB6174 Hexagon Thin Nut - B Grade - No Chamfer GB6175 II Hexagonal Nut - A, B Grade GB6176 II Type Hexagonal Nut - Fine Thread - A, B Grade GB6177 Hexagon Method Blue face nut - grade A GB55 hexagonal thick nut GB56 hexagonal super thick nut GB1229 large hexagonal nut (high strength for steel structure)
Further, the clamping mechanism includes two clamping plates placed between the two fixing blocks, a bearing seat is installed on one side of each of the clamping plates, a bearing is installed inside the bearing seat, and the bearing is The inner ring is snap-connected with an elastic adjustment screw, and the other end of the elastic adjustment screw penetrates the fixing block and is placed outside the fixing block.
The classification of the second combination screw is divided according to the material of the screw wire and the hardness index of the screw wire. Generally, the two combination screws are divided into stainless steel and iron, and stainless steel is divided into stainless steel 201, stainless steel 304 and stainless steel 316. Iron is divided into three types: low carbon steel, medium carbon steel, and high carbon steel. Carbon steel combination screws refer to iron combination screws. Generally, iron combination screws are classified into grades 4.8, 8.8, 10.9, and 12.9. But in the market, the combination screws of grade 10.9 and grade 12.9 are rarely used, so we won't talk about it here. And the two combination screws on the market are more commonly used combination screws of grade 4.8 and 8.8. 4.8 grade combination screws are generally made of 1010A screw wire rods. After the screw wire rods are beaten into screws, they are combined with spring flat washers. After production, this 4.8 grade combination screw does not need to be hardened. Its hardness can reach 4.8. The 8.8 grade combination screw is generally made of 10B21 screw wire. After the screw wire is punched into a screw, it is equipped with a spring washer and a flat washer, and the three pieces can be combined and rubbed by an automatic spring-flat washer machine. Fasten the spring-flat washer combination on the screw, and the spring-flat washer will not fall off. After the combination screw is produced, it needs to be hardened to make the hardness reach 8.8. After the hardness reaches 8.8, we need to take it for electroplating. In order to prevent hydrogen embrittlement of the spring washer in the 8.8-level combination screw with added hardness, it is easy to break. In this way, it is necessary to carry out hydrogen removal treatment on the hardened combined screws, and the electroplating can only be done after the hydrogen removal.
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 449N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
