What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
T-slot convenient bolt that can be used for the middle port of the T-slot and directly realizes the assembly and tightening of the bolt and the nut. Technical Background At present, the bolts for T-slots are assembled from two side ports of the T-slots. When the length of the T-slot is long, it is time-consuming and laborious to install from the side port to the center port at the designated position. In addition, the two side ports of the T-slot are often blocked by other components, and the bolts for the T-slot cannot be installed or removed without disassembling other components. The utility model makes some improvements to the prior art. SUMMARY OF THE INVENTION The purpose of the present invention is to provide a T-slot convenient bolt with simple structure and convenient mounting and dismounting for the current situation that the existing T-slot bolts are inconvenient to install and disassemble.
1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.
Common types of common screws All kinds of common screws (20 pieces) a. Slotted: a word ( Minus ) b. Phillips: cross ( Plus ) c. Phil-Slot: a word / cross d. Hex Socket: hexagon socket e. One Way: One-way (can only be locked in, not out) A-4: Head Code/ head shape. a. Flat: Flat head (after locking, the top is flush with the work piece) b. Oval: salad head, O head, countersunk head screw unit of measure screw unit of measurec. Round: round headd. Pan: round flat heade. Truss: large round flat headf. Hex: hexagon head. A-5: Finish Code/Appearance treatment. Metric Self-tapping screw: Mark Tapping Type directly behind the product name. Ex: M3 x 6 –PPB, Tapping Type: M3 self-tapping screw, 6mm long, cross, round flat head, black plated. Generally, it is determined by product type or mark. For Sheet Metal or plastic parts. *Pitch = Threads per inch
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 447N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
