What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Sprinkle the excess flat washer 6 on the positioning plate II3-1 on the flat washer positioning plate 3, and shake the flat washer positioning plate 3 by hand. After a short time, the flat washer 6 will be positioned and arranged on the upper positioning plate II3-1. In the flat washer hole 3-7, since the width of the opening groove 113-32 of the baffle plate II3-3 is smaller than the diameter of the flat washer hole 3-7, and the thickness of the upper positioning plate II3-1 is designed according to the thickness of the flat washer 6, each Only one flat washer 6 can be accommodated in the flat washer holes 3-7 of each upper positioning plate II3-1, and then use a brush to remove the excess flat washer
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 444N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
Blind rivets are a type of rivets for single-sided riveting, but they must be riveted with a special tool - a rivet gun (manual, electric, and moving). This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets (which must be riveted from both sides), so it is widely used in construction, automobiles, ships, aircraft, machinery, electrical appliances, furniture and other products. Among them, the open type oblate head blind rivets are the most widely used, the countersunk head blind rivets are suitable for riveting occasions that require smooth performance, and the closed blind rivets are suitable for riveting occasions that require higher load and certain sealing performance.
The flat gasket is a gasket whose upper and lower end faces are flat. The flat gasket used in the automobile differential is installed between the casing and the gear of the differential like the spherical gasket to reduce friction and reduce friction. Improve lubrication. The differential should accommodate severe bumps and be able to operate at high speeds for long periods of time in high and low temperature environments. Since both ends of the flat gasket currently used in the differential are smooth, or only one side end face of the flat gasket is provided with small concave points, during the high-speed operation of the differential, the flat gasket The lubrication of the contact surfaces is not ideal, and the friction between the contact surfaces is large, which is prone to failure.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
