What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
The national standard name of the cross recessed small pan head three combination screw is the cross recessed small pan head screw, the spring washer and the flat washer assembly. The national label is GB/T9074.8-1988. This 1988 refers to the year, that is, this standard is the standard issued by the country in 1988. The specifications of the cross recessed small pan head three combination screws, the company's minimum is M2.5, the shortest is 5mm, the largest is M10, and the longest is 90mm.
Surface treatment process of screws 1. Types of surface treatment: Surface treatment is the process of forming a covering layer on the surface of the workpiece by a certain method. The purpose is to give the surface of the product a beautiful and anti-corrosion effect. The following methods are as follows: 1. Electroplating: Immerse the part to be electroplated in an aqueous solution containing the metal compound to be deposited, and pass the current through the plating solution to precipitate and deposit the electroplated metal on the part. Generally, electroplating includes galvanized, copper, nickel, chromium, copper-nickel alloy, etc., and sometimes blackening (blue), phosphating, etc. are also included. 2. Hot-dip galvanizing: It is done by immersing the carbon steel parts in a zinc-melting bath with a temperature of about 510°C. The result is that the iron-zinc alloy on the surface of the steel gradually becomes passive zinc on the outer surface of the product. Hot dip aluminizing is a similar process. 3. Mechanical plating: The surface of the product is impacted by the particles of the plated metal, and the coating is cold welded to the surface of the product.
Align the four positioning holes 12-5 of the spring washer positioning plate 2 with the four positioning columns 4 of the screw tray 1, and place them on the screw tray 1. Several screws 5 are passed through the lower positioning plate 12-2 in turn. The spring washer hole 2-7, the opening slot 12-32 of the baffle plate 12-3, the inner ring of the spring washer 7 in the spring washer hole 2-7 of the upper positioning plate 12-1, hold the spring washer positioning plate 2 by hand The raised handle 12-31 of the baffle plate 12-3 pulls the baffle plate 12-3 out of the upper positioning plate 12-1 and the lower positioning plate 12-2, and several spring washers 7 pass through the holes on the lower positioning plate 12-2. The spring washer holes 2-7 fall down along the screw rod of screw 5, so that the screw rod of screw 5 penetrates into the spring washer 7, as shown in Figure 10, and then the spring washer positioning plate 2 is removed to complete the process of threading the spring washer.
rivet assembly device is provided with a base, the middle of the base is provided with a vertical groove, the bottom wall of the vertical groove extends forward and a horizontal convex block is suspended; the top surface of the convex block is fixed with a vertical rivet Needle and a guide column, the column body of the guide column is covered with a return spring; a downwardly open sliding block is mounted on the convex block, and the upper ends of the rivet needle and the guide column respectively protrude into the sliding block on the top wall of the sliding block. In the riveting pin hole and the guide hole, the inner wall of the riveting pin hole is provided with a large upper and a lower small horizontal step; the upper part of the bottom wall of the vertical groove is provided with a guiding limit rib. Guangdong Yueluo Hardware Industrial Co., Ltd. sets the rivet needle under the workpiece, and uses the upper die punch to press down the workpiece, and the rivet needle completes the operation of the rivet, omitting the operator to turn over and carry the rivet terminal board, thus effectively avoiding the rivet from The phenomenon that the rivet hole comes out. In addition, during operation, the workpiece is placed on the top surface of the slider, and the workpiece guide limit ribs and guide columns are used as shafts and radial limiters respectively. The riveting quality is good, and the purpose of saving time and labor and high efficiency is achieved.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
