What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
At present, most of the cylindrical pin press-fitting is to put the product into the positioning position of the lower die first, and then take a cylindrical pin and put it into a cylindrical pin positioning hole that is concentric and perpendicular to the hole in which the product is pressed, or put it on the product. , the pin needs to have a positioning guide; or it is fixed on the top of the indenter so that it will not fall, and then the press is completed. In fact, it is difficult to press the small cylindrical pins. To ensure the good quality of the product, it is required to locate accurately, to ensure that the cylindrical pins are concentric and vertical, and to put the cylindrical pins one by one. It is very easy for workers to produce. Fatigue and low efficiency, product quality control is affected by many human factors, resulting in unstable product quality and certain safety hazards in work. On the other hand, in some production lines, the cost of the press-in cylindrical pins is relatively expensive, such as finger cylinders and moving mechanisms, which will put a lot of cost pressure on the equipment investment of small and micro enterprises.
At present, the electrical control boxes of the market regulators all include a box body with built-in circuit board components and a box cover that is fastened together with it. The box cover is mostly fastened on the box body by self-supplied screws. The following problems are: First, there are many electric control lines on the circuit board in the box. When installing the self-supplied screws, the electric control lines may be damaged, which may easily cause a short circuit of the electric control, which is a potential safety hazard; Electric batch and other tools are inconvenient to install and disassemble, and the production cost is high.
Today's advanced manufacturing represented by large aircraft, large power generation equipment, automobiles, high-speed trains, large ships, and large complete sets of equipment has entered an important development direction. As a result, fasteners will enter an important stage of development. High-strength bolts are used for the connection of important machinery, and repeated disassembly or various installation torque methods require extremely high-strength bolts. Therefore, the quality of its surface condition and thread accuracy will directly affect the service life and safety of the host. In order to improve the friction coefficient and avoid corrosion, seizure or sticking during use, the technical requirements stipulate that the surface should be treated with nickel phosphorus plating. The thickness of the coating is guaranteed to be within the range of 0.02 to 0.03 mm, and the coating is uniform, dense, and free of pinholes.
ANSI B1.1 Thread Pitch Comparison Table Nominal Diameter (inch〖mm〗) Coarse Thread Pitch (UNC) Fine Thread Pitch (UNF) Ultra Fine Thread Pitch (UNEF) Drilling Diameter (Coarse Thread) Drilling Diameter (Fine Thread) #0 0.060 〖1.524〗 80 1.2 # 1 0.073 〖1.5 1.5 # 2 0.086 〖2.8 # 3 0.099 〖2.515〗 48 56 2.0 2.1 # 4 0.112 〖2.4 # 5 0.125 〖 3.175〗 40 44 2.5 2.6 # 6 0.138 〖3.50〗 32 40 2.7 2.9 # 8 0.164 〖4.166〗 32 36 3.4 3.5 # 10 0.190 〖4.0 # 12 0.216 〖5.486〗 24 28 32 4.5 4.6 1/4 6.35 20 28 32 5.1 5.4 5/16 10.7 11.5 9/16 〖14.288〗 12 18 24 12.3 13.1 5/8 〖15.875〗 11 18 24 13.5 14.7 3/4 〖19.05〗 10 16 20 16.7 17.5 7/8 〖22.125 2.4 9 14 〗 8 12 20 22.2 23.4 The pitch is expressed by the number of teeth per inch, such as: 11 teeth per inch, then the pitch=25.4/11=2.309mm. The unit of pitch in the table is the number of threads per inch. The hole diameter is the recommended hole size for tapping, in millimeters.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
