What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Figure 1 is a schematic structural diagram of Guangdong Yueluo Hardware Industry Co., Ltd. Figure 2 is a front view of the structure of the riveted positioning block. FIG. 3 is a top view of the structure of the riveted positioning block. Figure 4 is a front view of the structure of the riveting lower die. Figure 5 is a side view of the structure of the riveting lower die. 1, I is a rivet, 2 is a riveting positioning block, 3 is a product, 4 is another product, and 5 is a riveting lower die. [0017] Referring to Figure 2, Figure 3, 2-1 is a positioning pin, 2-2 is a rivet hole, and 2-3 is a through hole. Referring to Figure 4, Figure 5, 5-1 is a positioning hole, 5-2 is a guide block, 5_3 is a countersunk screw hole, and 5_4 is a vacant hole.
At present, in the power industry, for the fixing of terminals, most of the terminals are directly locked to the fixing screws using U-shaped clips. However, since the contact surface often cannot reach the level of flatness, it will cause difficulties in locking, and it will take a long time. Easy to loose and fall off. Although the use of spring clips is effective, due to the influence of its own width, the use of spring clips is not very extensive. Contents of the utility model The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to provide an automatic locking screw for fixing the U-shaped clip. In order to achieve the above purpose, Yueluo adopts the following technical solutions: an automatic locking screw. From bottom to top, there are screw head, screw rod and nut with external thread. The screw rod is a hollow screw rod, and the hollow screw rod is on both sides. Long holes are respectively provided, the width of the long holes is smaller than the inner diameter of the hollow screw rod, a spring is arranged in the inner cavity of the hollow screw rod, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole. The spring described by Yueluo is not less than the length of the hollow screw rod in the free extension state. The distance between the two wings of the plug described by Yueluo is greater than the diameter of the nut. Yueluo adopts Guangdong Yueluo Hardware Industry Co., Ltd., which can easily realize the automatic locking of the U-shaped clamp, and can be adjusted according to the thickness of the U-shaped clamp to ensure the close contact between the U-shaped clamp and the connecting screw.
In order to prevent the waste of materials, those skilled in the art select steel wire as the processing material, and form an annular ring body by drawing the steel wire. Such as the announcement: CN103522009's invention name is a method of processing a retaining ring. The steel wire is used as the processing material, and the processing is carried out by drawing. After the steel wire is drawn and formed, annealing is performed. After the annealing is completed, the forming needs to bundle the steel wire. Since the cross section of the steel wire is rectangular, when it is drawn into the retaining ring base, the cross section changes due to the extrusion of the material, and the inner ring of the retaining ring base will be higher than the outer ring (forming a slope). The deformation is large. At this time, the punching of the opening of the retaining ring base body will produce a slump or cause greater material deformation; therefore, the retaining ring base body needs to be bundled. The bundling process is to prevent the material from being heated more during the quenching process. At the same time, it also has a certain adjustment effect during the quenching process, which makes the inclined surface smaller; but after the quenching is completed, the hardness of the retaining ring base increases, and the punching process for the upper opening will become more complicated.
The four corners of the bolt head of the traditional T-slot connection bolt are all rounded corners, which will make the contact area between the bolt and the T-slot too small and reduce the connection fastness, especially when used for connection. When aluminum or copper profiles are used, due to the low hardness of the material, it is more likely to cause deformation of the T-shaped groove and affect the connection effect. Furthermore, since the traditional T-bolt has no direction indicator, it is difficult for the installer to identify the installation state during installation.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
