What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
In order to solve this technical problem, Yueluo Company provides an adjusting nut, which includes a bearing unit, a thrust washer, an adjusting nut and a snap ring. The inside of the adjusting nut is an internal thread structure, and one end of the internal thread structure is provided with Ring groove, the snap ring is pressed into the ring groove with interference, and is rigidly connected with the adjusting nut without relative movement; the bearing unit is supported on the shaft, and the thrust washer is in plane fit with the bearing unit; the adjusting nut and the shaft are threadedly connected , Fit with the thrust washer plane, the inner diameter of the snap ring and the thread of the shaft are in interference fit.
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 449N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35, and the screws enter the screw accommodating hole 46 from the discharge port through the guide rail 6. The slotting is carried out, which improves the efficiency and saves the labor cost.
Self-tapping screw is a kind of threaded fastener that self-tapping and drilling the matching female thread in the pre-drilled hole of metal or non-metal material. When using self-tapping screw, a flat washer is often required to protect the fastening surface. Traditional When the self-tapping screw is used, the flat pad is easy to fall off, resulting in low work efficiency. In view of this, we propose a combined structure of the stuck self-tapping screw spring washer that prevents the flat pad from falling off.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
