What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Service Hotline
+86760-8787 8587We have more than ten years of experience in screw industry production, the main products are: DIN562 square nut, hand screw nut, flange high nut, optional nut, iron clip nut crown screw, screw nut, extended super-long pull-out screw, SOO Pressure riveting parts, snap dog chain buckle carabiner nuts, O-rings, small edge washers, inch flat washers, PC board studs, industrial aluminum profile accessories type slider square nuts, standard screws and other fasteners, due to The materials and specifications of the products are different, and the prices are also different. Please contact us if you need it.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the shortcomings of the existing technology and provide a chip nut, which can improve the firmness and reliability of welding during welding, and at the same time, it can ensure that the welding is neat and beautiful. .
Commonly used standards are broadcast. For hexagonal nuts, the commonly used standards are: GB52, GB6170, GB6172 and DIN934. The main differences between them are: the thickness of GB6170 is thicker than that of GB52, GB6172 and DIN934, commonly known as thick screw cap. The other is the difference between the opposite sides, the opposite sides of DIN934, GB6170 and GB6172 in the M8 nut series are 13MM smaller than the opposite side 14MM of GB52, and the opposite sides of M10 nuts, DIN934 and GB52 are 17MM. The opposite side of GB6170 and GB6172 should be 1MM larger, M12 nut, DIN934, GB52's opposite side is 19MM larger than GB6170 and GB6172's opposite side 18MM is 1MM larger. For M14 nuts, the opposite side of DIN934 and GB52 is 22MM, which is 1MM larger than the opposite side of GB6170 and GB6172, which is 21MM. The other is the M22 nut. The opposite side of DIN934 and GB52 is 32MM, which is 2MM smaller than the opposite side of GB6170 and GB6172, which is 34MM. (Besides the thickness of GB6170 and GB6172 are the same, the width of the opposite side is exactly the same) The rest of the specifications can be used in general without considering the thickness.
At present, most of the cylindrical pin press-fitting is to put the product into the positioning position of the lower die first, and then take a cylindrical pin and put it into a cylindrical pin positioning hole that is concentric and perpendicular to the hole in which the product is pressed, or put it on the product. , the pin needs to have a positioning guide; or it is fixed on the top of the indenter so that it will not fall, and then the press is completed. In fact, it is difficult to press the small cylindrical pins. To ensure the good quality of the product, it is required to locate accurately, to ensure that the cylindrical pins are concentric and vertical, and to put the cylindrical pins one by one. It is very easy for workers to produce. Fatigue and low efficiency, product quality control is affected by many human factors, resulting in unstable product quality and certain safety hazards in work. On the other hand, in some production lines, the cost of the press-in cylindrical pins is relatively expensive, such as finger cylinders and moving mechanisms, which will put a lot of cost pressure on the equipment investment of small and micro enterprises.
GB97.1.CATPart GB97.1.SLDPRT Nominal size d d1 d2 h 1000 weight (kg) ≈ nominal diameter (NND) inner diameter (SD1) outer diameter (SD2) thickness (SD) — 5 5.3 10 1 0.443 Spring washer spring Wasket 6 6.4 12 1.6 1.0518 8.4 16 1.6 1.828 10 10.5 20 2 3.57 14 15 28 2.5 8.611 16 17 30 3 11.29 20 21 37 37.16 24 25 44 4 32.31 30 31 56 4 53.61 36 37 66 5 92.03
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
What is the tolerance range of precision screws?
How to choose the right stainless steel screw manufacturer?
Why is there an R angle under the head of the hexagon head s...
We have more than ten years of production experience in the ...
We have more than ten years of production experience in the ...
We have more than ten years of experience in screw industry ...
We have more than ten years of experience in screw industry ...