Wholesale Grade 12.9 Alloy Steel Cylindrical Head Socket Head Cap Screws Bolts Cup Head Screws 3/4

We have more than ten years of experience in screw industry production. The main products are: British and American locking nuts, carbon steel square head bolts, national standard T-shaped square nuts, full-thread bolts, set electronic screws, GB901 blackened stud bolts, fine thread Hexagon flat nuts, GB5783 screws, nylon plastic bolts, horizontal pin square key pins, outer hexagonal insulating bolts, non-standard hollow rivets, hot-dip galvanized hexagonal nuts, copper outer hexagonal bolts, link buckle carabiner chain buckle and other fasteners, Due to the different materials and specifications of the products, the prices are also different, please contact us if necessary.

Online consultationMobile hotline
132 6870 6820
Product introduction

Screw Specifications

Screw head table

Hex cap screw and Hex bolt Hex bolt As the name suggests, it is a male threaded fastener with a hexagonal head, designed to be turned with a wrench. According to the ASME B18.2.1 standard, the head height and shank length tolerance of the hexagon head screw (Hex cap screw) is smaller than that of the general large hexagon bolt (Hex bolt), so ASME B18.2.1 hexagon screw is suitable for installation in all hexagon bolts that can be used. places, also including places where the large hex bolts are too large to be used. The screw head of the hexagon socket screw is round on the outside, and the middle is a concave hexagon, and the hexagon screw is the kind of common hexagonal screw head. The hexagon socket head screwdriver looks like a '7'. Cut two sections of a hexagonal steel bar and bend it at 90 degrees to form a hexagon socket head screw wrench, which is sold in hardware tool stores. Hexagon socket screwdrivers are not so-called mobile phone special screwdrivers. Mobile phone special screwdrivers can be bought at the booths that sell repair tools in the electronics market. Hexagon socket head cap screws are often used in machinery, mainly because they are easy to fasten, disassemble, and not easy to slip. The Allen wrench is generally a 90° bend. One end of the bend is long and one side is short. When using the short side to drive screws, holding the long side can save a lot of force and tighten the screws better. The long end has a round head (a hexagonal cylinder is similar to a sphere) and a flat head. The round head can be easily slanted and disassembled, and some parts that are inconvenient to lower the wrench can be installed. The manufacturing cost of the outer hexagon is much lower than that of the inner hexagon. Its advantages are that the screw head (the force position of the wrench) is thinner than the inner hexagon, and some places cannot be replaced by the inner hexagon. In addition, machines with low cost, low power strength and low precision requirements use much less hexagon socket screws than external hexagon screws. [1] Socket cap screw, also known as socket head screw or Allen bolt, is a screw with a hexagonal inner hole on the head, with a hexagonal ruler (hex key, Allen wrench or Allen key) Tighten or loosen only after inserting into the inner hole. The most commonly used hexagon socket head screws are cylindrical head screws with a head diameter of about 1.5 times the main diameter of the thread (1960 series). Countersunk head cap screw. The countersunk hole design allows the screw head to be rotated without being exposed on the surface of the fixed object, so it is mostly used in places where the surface is small and it is inconvenient for traditional wrenches to use.

Wholesale Level 12.9

The materials of rubber gaskets are usually NBR (nitrile butadiene rubber), SBR (styrene butadiene rubber), HNBR (hydrogenated nitrile butadiene rubber), EPDM (EPDM rubber), SILICONE (silica gel), VITON (fluorine rubber), CR ( Neoprene), FFKM (perfluoroelastomer), etc.

Alloy Steel Cylinder Head Socket Head Cap Screws

bolt

The t-bolt can be directly put into the groove of the aluminum profile. It can be automatically positioned and locked during the installation process. It is often used in conjunction with the flange nut. profiles to choose from. T-bolts are movable anchor bolts. Bolt: A mechanical part, a cylindrical threaded fastener with a nut. A type of fastener consisting of a head and a screw (a cylinder with an external thread) that needs to be matched with a nut to fasten and connect two parts with through holes. This form of connection is called a bolted connection. If the nut is unscrewed from the bolt, the two parts can be separated, so the bolt connection is a detachable connection. There are hexagonal head, round head, square head, countersunk head and so on. Among them, the hexagonal head is commonly used. Generally, the countersunk head is used in places where the surface is required to be smooth without protrusions, because the countersunk head can be screwed into the part. Round heads can also be screwed into parts. The tightening force of the square head can be larger, but the size is large.

Cup head screw

The spring self-locking nut is a spring clip self-locking nut, which consists of an S-shaped spring clip and a self-locking nut. The S-shaped spring clip is provided with a fixing hole (3) for fixing the self-locking nut, which is used for the transition through the bolt. The self-locking nut is placed between the clamping hole and the transition hole (4), and is clamped in the clamping hole. The utility model adopts the elastic force of the spring clip to fix the self-locking nut on the connecting plate or the support. Not only is it convenient to install, but also has good reliability after installation.

3/4

The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].

Cooperation Case

Hot Recommend