What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Installation method broadcast 1. One-time burying method: When pouring concrete, bury the anchor bolts. When the high tower is controlled by overturning, the anchor bolt should be buried once. 2. Reserved hole method: The equipment is in place, the holes are cleaned, the anchor bolts are placed in the holes, the equipment is positioned and aligned, and then poured with non-shrinkage fine stone concrete that is one level higher than the original foundation, and compacted and compacted. . The distance from the center of the anchor bolt once buried to the edge of the foundation should not be less than 2d (d is the diameter of the anchor bolt), and should not be less than 15mm (d≤20, it should not be less than 10mm), not less than half the width of the anchor plate Add 50mm, when the above requirements cannot be met, appropriate measures should be taken to strengthen it. The diameter of the anchor bolts used for the structure should not be less than 20mm. When subjected to earthquake action, double nuts should be used for fixing, or other measures to effectively prevent loosening should be adopted, but the anchorage length of anchor bolts should be increased by 5d compared with the anchorage length of non-seismic action. Installation planning of anchor bolts Treatment of anchor bolts loose in the foundation When the anchor bolts are tightened, the bolts may be pulled out. At this time, the bolts should be adjusted to their original positions, and the foundation around the bolts should be shoveled out enough. , and then weld two U-shaped steel bars vertically and horizontally on the bolts, and finally clean the pit with water and grouting, and then tighten the live anchor bolts after the concrete has solidified to the design strength. The treatment method of the live anchor bolt deviation is roughly the same as the dead ground. The method for the anchor bolts is the same, except that the anchor bolts can be pulled out for processing. If the bolt is too long, a section of the thread can be cut off on the machine tool; if the bolt is too short, it can be extended by hot forging; if the position is inconsistent, it can be corrected by bending. Application industry: suitable for various equipment fixing, steel structure foundation embedded parts, street lights, traffic signs, pump, boiler installation, heavy equipment embedded fixing, etc.
In order to achieve the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solutions: an anti-drop screw structure, including a connecting bolt and a fastening screw, the connecting bolt includes a connecting screw and a connecting nut, one end of the connecting screw It is integrally connected with the connecting nut, the surface of the connecting screw is provided with an external thread, the connecting bolt is movably mounted with a matching nut, the matching nut and the connecting bolt are connected by thread, and the interior of the connecting screw is provided There is a screw hole along the axis of the connecting screw. The connecting screw is provided with a number of slots along the axis. The slot extends into the screw hole. The screw hole is provided with an internal thread, and the screw hole is movable in the screw hole. A tightening screw is installed, the tightening screw includes a tightening screw and a tightening nut, one end of the tightening screw is integrally connected with the tightening nut, and the tightening screw is connected to the tightening nut through a screw hole Bolted thread connection.
As we all know, bolt and nut kits are commonly used fastening parts, but when ordinary bolt fasteners are used in a large number of parts, because the nuts and bolts are engaged by threads, manual or machine tightening is required, and during installation, It is easy to slip, and the bolts need to be operated in both directions, and a pair of bolts and nuts cannot be installed quickly, which reduces the installation efficiency.
The front wall sound insulation pad is used to absorb the heat and noise transmitted by the firewall, and also plays the role of heat insulation and vibration isolation, ensuring a relatively quiet and comfortable environment in the car and improving ride comfort. As shown in FIGS. 1 and 2 , the front wall sound insulation and heat insulation pad 101 is generally fixed to the vehicle body by means of screw buckles 102 . The screws 100 are clamped by the clamping feet 103 in the screw The limiting rib 104 clamps the screw 100. After the screw 100 is clamped into the screw buckle 102, the tail end of the screw 100 is exposed, which is easy to scratch the operator when assembling other components, and the exposed screw 100 is easy to cause corrosion, thereby affecting the connection strength of the screw 100, and also The service life of the screw 105 is reduced.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
