What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
At present, due to the installation position determined in the design process of the traditional thrust cylinder in China, the corresponding position of the piston rod and the clamping arm is fixed, and it is impossible to ensure that the workpiece can be clamped while the workpiece is thin. It is not conducive to the use of such products when clamping. Secondly, when the workpiece is assembled or welded, it not only needs to be tightened in a certain direction, but also needs to be positioned, so as to ensure the accuracy required for processing. When a workpiece is fixed in this way, it must be realized by adding a mechanism, which will increase the complexity of the system and bring inconvenience to installation and maintenance.
Axle card is a kind of hole-to-hole movement installed on a slotted shaft and used as a fixed component. The inner diameter of this type of retaining ring is slightly smaller than the diameter of the assembly shaft. Application No. 201621153710.9 discloses a shaft card assembly device, including a feeding mechanism, a material distribution mechanism, a material reclaiming mechanism and an assembling mechanism. The feeding mechanism is connected with the feeding mechanism. The reclaiming mechanism includes a reclaiming tool and a servo system for driving the movement of the reclaiming tool. One end of the reclaiming tool is provided with a c-shaped opening, and an incision connected with the c-shaped opening is provided. The assembling mechanism includes a carrier for fixing the parts to be loaded and a turntable, and the carrier is mounted on the turntable. In the above shaft card assembly device, after the feeding mechanism completes the feeding, the material distribution mechanism separates the shaft card to a specific position with a fixed attitude, and then the private server drives the reclaiming tool to clamp the shaft card and assemble it to the pre-fixed by the assembly mechanism. on the fitting. During the assembly process, the manual workload is small, the efficiency is high, and the labor intensity is small. At the same time, the c-shaped opening and the cutout at the end of the reclaiming tool are designed to effectively form an elastic force to clamp the clamping shaft card and absorb the assembly process. The resulting outward deformation force avoids the plastic deformation of the shaft card due to the large external force.
ANSI B1.1 Thread Pitch Comparison Table Nominal Diameter (inch〖mm〗) Coarse Thread Pitch (UNC) Fine Thread Pitch (UNF) Ultra Fine Thread Pitch (UNEF) Drilling Diameter (Coarse Thread) Drilling Diameter (Fine Thread) #0 0.060 〖1.524〗 80 1.2 # 1 0.073 〖1.5 1.5 # 2 0.086 〖2.8 # 3 0.099 〖2.515〗 48 56 2.0 2.1 # 4 0.112 〖2.4 # 5 0.125 〖 3.175〗 40 44 2.5 2.6 # 6 0.138 〖3.50〗 32 40 2.7 2.9 # 8 0.164 〖4.166〗 32 36 3.4 3.5 # 10 0.190 〖4.0 # 12 0.216 〖5.486〗 24 28 32 4.5 4.6 1/4 6.35 20 28 32 5.1 5.4 5/16 10.7 11.5 9/16 〖14.288〗 12 18 24 12.3 13.1 5/8 〖15.875〗 11 18 24 13.5 14.7 3/4 〖19.05〗 10 16 20 16.7 17.5 7/8 〖22.125 2.4 9 14 〗 8 12 20 22.2 23.4 The pitch is expressed by the number of teeth per inch, such as: 11 teeth per inch, then the pitch=25.4/11=2.309mm. The unit of pitch in the table is the number of threads per inch. The hole diameter is the recommended hole size for tapping, in millimeters.
The application range of the oil pump is very wide. When it is used, the oil pump needs to be assembled. During the assembly process, when the pin is driven into the pin hole, it is generally held by the operator with a hammer, and then aiming at the top of the pin to press. Into the hole, due to the relatively high tolerance requirements for the depth of the pin pressing and the side clearance (the gap between the pin and the groove wall), the traditional operation method not only causes a high rejection rate and a long training time for personnel, but also The slow processing speed affects the production efficiency.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
