What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Related Specifications of Automobile Welding Nuts (Square Nuts) Serial Number Standard Number Name (English) Name (Chinese) Remarks 1 MS440014 NUT,WELD Welding Square Nut M8 2 MS440013 NUT,WELD (6) Welding Square Nut M6 3 MF445605 NUT,WELD (10 ) welding square nut M10 4 MU442002 NUT,WELD welding square nut M6 parking brake handle 5 MB077464 NUT,WELD welding square nut for seat belt welding square nut 6 MB040348 BOLT WELD (10X22) welding bolt M10×22, bearing surface 7 MF198353 BOLT,WELD (6X14) Weld bolt M6×14, end face 8 MR236366 NUT (12) Nut M12 Suspended trailing arm mount 9 MS440015 NUT,WELD (10) Weld square nut M10 10 PW832525 BOLD WELD 7/16 UNF Weld bolt 7/16 For seat belt, bearing surface 11 MB528563 STUD,WELD Welding stud M6×20 12 MS440066 NUT,WELD (5/16=18UNC) Welding square nut 5/16 Child safety system 13 MS440018 NUT, WELD (6) Welding square nut M6 14 MF198375 BOLT,WELD (8X30) Welding stud M8×30 15 MF198038 BOLT, WELD (6X25) Welding bolt M6×25, bearing surface 16 MR236467 NUT (12) Welding square nut M12, for engine mount 17 MF140024 BOLT, FLANGE (8X18) Hexagon flange bolt without 3D 19 MF198036 BOLT,WELD (6X20) Weld stud M6×20 20 MF198034 BOLT,WELD (6X16) Weld bolt M6×16, bearing face 21 MS440012 NUT,WELD (5) Weld Square Nut M5 22 MB343340 BOLT,WELD (8X26) Welding Bolt M8×26, Bearing Surface 23 MB138471 STUD,WELD Welding Stud M8×46, Bearing Surface 24 MS190066 BOLT,WELD (8X16) Welding Bolt M8×16, Bearing Surface, NO 3D 25 MS240145 BOLT,WASHER ASSEMBLED (8X20) BOLT AND WASHER ASSEMBLY NO 3D 26 MB281149 NUT,WELD(6) WELD BOLTS M8, NO THREADS REQUIRED FOR BEARING 27 MF445603 NUT,WELD (6) Welded square nut M6 Reinforcing plate for rear door lock 28 MS190068 BOLT,WELD (8X20) Welded bolt M8×20, bearing surface 29 MU431507 NUT,WELD Welded square nut M8 for door hinge installation 30 MS240121 BOLT,WASHER ASSEMBLED (6X16) Bolt and washer assembly M8 for fuel filler cap 31 MS100221 BOLT,FLANGE (6X12) Flange face bolt M6 for fender mounting 32 MB344675 STUD,WELD Weld stud M6×10
When used for the connection and fixation of doors, windows, cabinets, etc. involving hinges, the traditional screw fastening method is usually used, and the screws are directly driven into the screw holes of the connected parts, and the screw end caps are directly exposed, which not only affects the connected parts. Moreover, the end caps of the screws exposed for a long time are easy to rust, and there are burrs in the end processing of the general screws. When used for fastening connections, the end caps of the screws are easy to scratch people, which affects the appearance and is not safe.
1. Material strain hardening When the material is cyclically loaded, the phenomenon of cyclic strain hardening or cyclic strain softening will occur, that is, under the condition of constant cyclic strain, the stress amplitude will increase or decrease with the increase of the number of cycles. . After several cycles, the stress amplitude enters a cyclic steady state. The low-cycle fatigue of the lock nut is carried out under the condition that the strain is constant, and the strain hardening or softening of the threaded piece will affect the size of its maximum unscrewing torque. The alloy steel used to make the lock nut is a cyclic strain hardening material, and the hardening of the material will increase the elastic restoring force FN of the threaded sheet and increase the unscrewing torque.
T-bolts have been widely used in the fields of aviation, aerospace and defense due to their good positioning and anti-shedding effects. Its related standards have special requirements for accurate positioning, anti-falling off, and dimensional consistency of T-bolts. This requires that the position, size and shape and position tolerance of the anti-fall hole of the T-bolt shank must be controlled within a certain range. Therefore, the processing method of the anti-shedding hole is particularly important. Since the machined anti-shedding hole is located at the position of the rod, the milling processing efficiency is too low, the product cost is high, and there is a large machining error. When conventional drilling is used, the consistency of the anti-shedding hole size cannot be guaranteed. To solve the above problems of low efficiency and dimensional instability
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
