What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
The gasket is a part that is placed between the connector and the nut, and is generally a flat metal ring. Gaskets are used for mechanical seals between two objects, usually to prevent pressure, corrosion, and natural thermal expansion and contraction of pipes between two objects and leakage. Since machining the surface is not possible, irregularities can be filled with spacers. Gaskets are typically made from sheet materials such as backing paper, rubber, silicone rubber, metal, cork, felt, neoprene, rubber, fiberglass, or plastic polymers such as Teflon, application-specific gaskets May contain asbestos. Other uses are as spacers, springs (Belleville spacers, wave spacers), wear pads, pre-display devices, lock devices. Rubber gaskets are also used in faucets (valves) to cut off the flow of liquid or gas, and rubber or silicon gaskets are also used to reduce fan vibration. The function of ordinary gaskets is not good, the gaskets are easy to slip during the nut pressing process, the tightening effect is poor, the wear resistance of the gaskets is not good, and it has no anti-interference effect when used in electronic components.
Stud bolts are manufactured in accordance with GB897-GB901 standards, the materials used are: Q235, 45#, 40Cr, 35CrMoA, Q345D, the specifications are: M3mm-M100mm, and the length can be customized according to user needs. High strength stud bolts, materials are 35#, 45#, 35CrMoA, 25Cr2MoV, 304, 316, 304L, 316L, 2H, 2HM, B7, B7M, B16, B8, 8, B8M, 8M, widely used in electric power, chemical industry , oil refining, valves, railways, bridges, steel structures, automobile and motorcycle accessories and other fields: generally used in mining machinery, bridges, automobiles, motorcycles, boiler steel structures, pendant towers, long-span steel structures and large buildings, etc. . Representation method of stud bolts: General stud bolts are expressed as: M12×100 GB 901-88 (standard) 35#/35# (material) 8.8 grade/8 grade (modulation grade) means: diameter = 12mm length = 100mm GB 901-88 adopts the national standard (of course, the industry standard can also be used as needed) stud bolt standard: GB 900-1988 Introduction to stud bolts Stud bolts save time and cost All stud bolt structures do not require drilling, Steps such as punching, threading, riveting, threading and finishing continue to expand the application potential of structural design, high current and small penetration. Therefore, welding to very thin sheets is possible. The workpiece for stud welding must be welded from one side. Can be soldered in all positions, with the help of extenders on vertical bulkheads that can be restricted. Since it is welded for a short time and there is little deformation after welding, no trimming is required. Because the welded structure does not require drilling, there is no leakage. The joint can achieve high strength, that is, the joint strength of stud welding is greater than the strength of the stud itself. How to install studs Good economy The advantage of other welding methods is the welding power. For mass-produced workpieces, standard studs are low cost. There are various types of equipment and welding torches, and the acquisition cost of equipment is relatively low. According to the product, it can be made into a multi-station automatic welding machine, or a high-precision gantry-type CNC automatic welding machine. Stud welding has high quality reproducibility and low rejection rate. However, in the application of stud welding, it should be noted that, like other fusion welding, there are certain restrictions on the carbon content in the steel. For structural steel studs, welding should be performed according to the recommended combination of stud material and base metal. There will be infusibility with the base metal. Combinations of stud material and base metal outside the recommended range shall be tested to determine the weldability and the product design requirements of the anchor bolt for the possibility of relevant inspection and evaluation.
A T-bolt. This kind of bolt includes a bolt shank and a bolt head, and the bolt head adopts a special cylindrical bolt head, which can be suitable for installation and cooperation of various sizes. Although the shape of such a bolt head is greatly improved compared to the square bolt head in the prior art, the cylindrical bolt head is particularly inconvenient to install, and special installation tools must be used for installation. If the manual direct installation method is adopted, since the force area of the finger touching the side of the cylinder is small, it will increase the difficulty of the installation work and needs to be improved.
As shown in Figures 1 and 2, Yueluo is an automatic locking screw. From bottom to top, there are screw head 1 with external thread, screw rod and nut 3. The screw rod is a hollow screw rod 2, and the hollow screw There are long holes 7 on both sides of the rod 2, the width of the long hole 7 is smaller than the inner diameter of the hollow screw rod 2, and a spring 4 is arranged in the inner cavity of the hollow screw rod 2, and the spring 4 is not smaller than the hollow screw rod 2 in the free extension state. The upper end of the spring 4 is provided with a plug 5, the distance between the two wings 6 of the plug 5 is greater than the diameter of the nut 3, and the two wings 6 of the plug 5 protrude out of the hollow screw rod 2 through the long hole 7. When using the Yueluo, you only need to compress the spring through the two wings, insert the U-shaped clip after the neutral position is exposed, and then release the two wings, the spring will automatically return and compress the U-shaped clip, which is easy to use, safe and reliable. Claim 6. An automatic locking screw, from bottom to top, is a screw head, a screw rod and a nut provided with an external thread, characterized in that the screw rod is a hollow screw rod, and both sides of the hollow screw rod are respectively provided with Long hole, the width of the long hole is smaller than the inner diameter of the hollow screw rod, the inner cavity of the hollow screw rod is provided with a spring, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
