What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
The produced screws, due to unreasonable production aspects, are likely to cause quality problems in the screws. During production, many screw quality problems may be found upon delivery. Let's talk about the quality problems often encountered by screws and the reasons for the quality problems, and finally put forward some solutions. 1. The head of the screw is deformed and the head is crooked. The possible reasons are the poor installation of the first punch of the screw die and the improper adjustment of the machine. 2. The head of the screw is not round. The reason is that the selection of the first punch of the screw mold is improper or the first punch is not full enough. 3. The screw has burrs or burrs. The reason is the poor forming of one punch, mainly caused by too large gap between punch and die hole or too short punch. 4. The screw head is cracked and the screw head is cracked. The reason may be that there is a problem with the quality of the screw wire itself, so before the screw wire is headed, the quality department must check it and use the potion. Especially the stainless steel screw wire, it is necessary to check that it is stainless steel 201 and that is stainless steel 304. It is also possible that a die is used incorrectly (such as a die with a hexagonal washer head for a pan head), and the viscosity of the lubricating oil fails. For the problem of the screw head, you can read the article written by Manager Zhu above - high-strength screw fracture or head crack detection. In this article, some problems encountered by the screw head and how to detect the screw head problem are clearly introduced [4]. The common quality reasons for screws are of course more than the above, this is only part of it. There are other quality issues, then Manager Zhu will talk about it. The above screw quality reasons are for reference. If you encounter these problems, you can try the solutions proposed.
When installing the ventilation duct, because the gap between the air duct and the wall and between the air duct and the air duct is deep and narrow, the arm cannot enter into it to operate, which brings about the installation of the screws and nuts at these positions. The following three methods are generally used: one is to directly break the wall for installation, but this method damages the building greatly, and cannot be used for the installation of screws and nuts in the gap between the air ducts; the other is to Set the inner flange in the air duct and connect it with bolts, which will reduce the effective cross-sectional area of the air duct and increase the resistance of the gas flow. Moreover, people need to enter the air duct for construction during installation. Considering the size of the air duct First, the supporting firmware with a high position and no force has certain hidden dangers; third, it is directly ignored and not done, but it is easy to cause the air duct connection is not tight and the air volume loss is large. The above-mentioned methods all have major construction defects, which not only waste a lot of manpower and time in the construction process, but also have the problem of low air supply efficiency.
In view of the above situation, the technical problem to be solved by Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a self-expanding semi-solid installation rivet, the purpose is to solve the existing connection between plastic shells, lightweight plates, insulating materials, circuit boards, or any other In the case of thin, light-weight materials, the grip and bonding force of the rivet itself on the mounting surface is weaker than that of the rivets that are screwed and installed by manual operation. The rivet structure needs to be improved and strengthened when the material is installed.
Guangdong Yueluo Hardware Industry Co., Ltd. relates to a connecting piece, especially a wood screw used for fixing on non-rigid materials such as wood or plastic. Guangdong Yueluo Hardware Industry Co., Ltd. has a threaded part with a taper angle and a screw head. The head of the screw can be countersunk, hemispherical, or other shapes. As for the grooves for screwing, the grooves can be straight-line grooves, concave cross grooves, or grooves of other shapes.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
