What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
When the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
The main function of the spring washer is to prevent the nut from loosening. It is also known that: the existing spring washer is a ring made of spring steel, and then a gap is cut in the diameter direction on the ring, and the heads on both sides of the gap are cut. The material of the part is turned to two different sides of the ring to form a pawl, and the purpose of preventing loosening is achieved by the fit between the pawl and the nut on the surface and the workpiece. Obviously, only one pawl is used to achieve the purpose of preventing loosening. Since the braking force generated by one pawl is limited, there are defects of poor braking effect and poor anti-loosening effect.
The meaning of bolt performance grade is an international standard. Bolts of the same performance grade, regardless of the difference in material and origin, have the same performance, and only the performance grade can be selected in the design. Strength grade The so-called 8.8 and 10.9 grades refer to the shear stress grades of bolts of 0.88GPa and 1.09GPa 8.8 Nominal tensile strength 800N/MM2 Nominal yield strength 640N/MM2 General bolts use XY to indicate the strength, X *100=tensile strength of this bolt, X*100*(Y/10)=yield strength of this bolt (because according to the regulations: yield strength/tensile strength=Y/10, that is, 0.Y is the yield strength ratio ) If the grade is 4.8, the tensile strength of this bolt is: 400MPa; the yield strength is: 400*8/10=320MPa. Another: stainless steel bolts are usually marked as A4-70, A2-70, and the meaning is otherwise explained Measurement: There are two main units of length measurement in the world today, one is the metric system, and the measurement unit is meters (m) and centimeters (cm). ), millimeter (mm), etc., are used more in Europe, my country and Japan and other Southeast Asian regions, the other is the British system, and the unit of measurement is mainly inches (inch), which is used more in the United States, Britain and other European and American countries. 1. Metric measurement: (decimal system) 1m2 =100 cm2=10000 mm2, imperial measurement: (8 decimal system) 1 inch = 8 inches 1 inch = 25.4 mm 3/8¢¢×25.4 =9.523, 1/4 ¢¢ The following products are indicated by their number, such as: 4#, 5#, 6#, 7#, 8#, 10#, 12#
Slotted Round Head Wood Screws GB 99-86 Slotted Countersunk Head Wood Screws GB 100-86 Slotted Half Countersunk Head Wood Screws GB 101-86 Hexagon Head Wood Screws GB 102-86 Cross Recessed Round Head Wood Screws GB 950-86 Cross Slotted countersunk head wood screws GB 951-86 Cross recessed countersunk head wood screws GB 952-86
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
