What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35 , and the screws enter the screw accommodating hole 43 from the discharge port through the guide rail 6 . The slotting is carried out, which improves the efficiency and saves the labor cost.
The standard specifies hexagon head bolts with thread specifications of M3~M64, grades A and B. Grade A is used for bolts with D<=24 and L<=10D or L<=150mm (whichever is smaller); grade B is used for bolts D > 24 or L > 10 D or L > 150 (according to the smaller value) bolt size specification mark: thread specification D = M12, nominal length L = 80mm, performance level is 8.8, the table is the same as oxidation, A level Hexagon head bolt tag example bolt GB / T5782-86-M12 × 80 national standard common hex bolt head on the side size and cooperation national standard wrench thread diameter \ pair of edge sidewalls Skin wrench Wrench Double-ended open-end wrench Double-ended Torx wrench. The outer hexagon bolt is the most frequently used type of bolts. The main function of the external thread it has is to cooperate with the nut. Using this threaded connection method, the two parts are integrated. Grade C hexagon bolts are mainly used in steel structure machinery and equipment with relatively rough surface and low precision requirements. Grade A and Grade B hexagon bolts are mainly used in machinery and equipment with smooth surface and high precision requirements. Most of the stainless steel outer hexagon screws are full-tooth and hexagonal head full-tooth bolts. Standard: DIN933, GB5783, ISO4017, ANSIB18. 2.1, JISB1180; non-full thread bolt standards DIN931, GB5782, ISO4014, ANSIB18.2.1, JISB1180.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
Therefore, there is a need to design a bearing retaining ring disassembly and installation device that facilitates the installation and disassembly of the bearing retaining ring, and is safe and reliable.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
