What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
For the detection of the shear force of the elastic cylindrical pin, the method and the tooling are marked, but the tooling is only a means to be used on the test bench, and the process of embedding the cylindrical pin into the tooling is a more difficult process. Generally, it is used to place the tooling on a plane, a vise, a simple V-shaped, and a simple U-shaped fixture. Originally, the elastic cylindrical pin was detected by hand or pliers to hold the cylindrical pin and align the pin with the outer cylinder of the tooling. Use a hammer to smash the shear holes, and adjust the concentricity of the inner and outer cylinders of the shear holes of the tooling from time to time. The limitations, dangers and difficulties of this assembly method are relatively large, often testing a set of cylindrical pins, which takes a lot of time and is difficult for lesbians to complete.
The production of non-standard round flat pads can only be processed on ordinary lathes without punching machines. Processing with round steel is difficult, material waste is large, tool loss is large, and efficiency is low. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a non-standard circular flat pad lathe processing fixture, which is suitable for the production of various non-standard circular flat pads. Yueluo is realized in this way. It includes a hollow square support, a bolt and a circular machining groove. It is characterized in that a circular machining groove is left on one surface of the hollow square support. There are 4 bolts evenly connected. The advantages of Yueluo are: 1. Reduce the difficulty of processing; 2. Save materials (can use corner waste); 3. Reduce tool wear; 4. Improve production efficiency.
Lock washers feature easy installation. 1. Just place the helical tooth surfaces on the inner side of the two washers against each other and place them between the nut and the connecting material; 2. After the nut is tightened, the radially convex surface on the outer side of the lock washer and the contact surfaces at both ends are in an engaged state, and The angle of the slope angle of the helical tooth surface on the inner side of the washer is greater than the thread angle of the bolt; 3. When the bolt is elongated due to mechanical vibration, the nut will rotate and loosen accordingly. Because the frictional force of the outer radial convex surface of the lock washer is greater than the frictional force between the inner helical tooth surfaces. In this state, only the relative dislocation between the inner helical tooth surfaces is allowed to generate a certain lifting tension; 4. When the bolt shrinks, the helical tooth surface of the washer will make the nut return to its original position. So as to achieve 100% anti-loose and tightening effect; 5. Washers are suitable for relatively flat and smooth surfaces; 6. If the connecting material is non-metallic material, a metal plate can be fixed on the connecting material, so that the Use the lock washer; 7. There is no need to use a torque wrench when installing the lock washer; 8. You can choose to use an air tool when installing or removing the lock washer.
NPT, PT, G are all pipe threads. NPT is the abbreviation of National (American) Pipe Thread, which belongs to the American standard 60-degree taper pipe thread, which is used in North America. National standards can be found in GB/T12716-1991 PT is the abbreviation of Pipe Thread, which is a 55-degree sealed conical pipe thread, which belongs to the Whitworth thread family and is mostly used in Europe and the Commonwealth of Nations. Commonly used in water and gas pipe industry, the taper is specified as 1:16. The national standard can be found in GB/T7306-2000 G is a 55 degree non-threaded sealing pipe thread, which belongs to the Whitworth thread family. Marked as G stands for cylindrical thread. National standards can be found in GB/T7307-2001 In addition, the 1/4, 1/2, 1/8 marks in the thread refer to the diameter of the pipe, and the unit is inches. People in the industry usually refer to thread size in points, 1 inch equals 8 points, 1/4 inch is 2 points, and so on. G seems to be the general name for pipe threads (Guan), and the division of 55 and 60 degrees is functional, commonly known as pipe circle. That is, the thread is machined from a cylindrical surface. ZG is commonly known as pipe cone, that is, the thread is made of a conical surface. The general water pipe joints are like this. Rc means conical internal thread ZG means taper pipe thread, 3/4 means inch mark, which is 3/4 inch conical pipe Thread, there is in the Hardware Manual. The national standard stipulates that the major diameter of ZG 3/4 thread is 26.44 mm. Please refer to Metric, American and British Thread Standard Manual (Third Edition). Its representation method should be: ZG 3 /4″. Among them (〃) is the representative symbol for inches. One inch is equal to 8 inches. The origin of 3/4 is 6/8=3/4. Commonly known as 6 points. Similarly, the major diameter of ZG 1/2″ thread≈21 mm. Commonly known as 4 points. ZG 1″ thread diameter ≈ 33 mm. Commonly known as 1 inch. ZG 1 1/2″ thread pipe outer diameter ≈ 48 mm. Commonly known as 1 inch and a half. Taper pipe thread is very similar to pipe thread, the difference is Only in the taper. Note that the basic size of the pipe thread and ordinary thread is different. DN is the nominal diameter
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
