Service HotlineSpecification label broadcast representation format: Thread specification d=M12, nominal length L=80mm, and performance level 4.8 equal-length stud bolts are completely marked as: GB 901 M12×80 [1] Product example: Stud studs are generally required After surface treatment, there are many types of bolt surface treatment, commonly used are electroplating, blackening, oxidation, phosphating, electroless zinc flake coating treatment, etc. However, electroplated fasteners account for a large proportion of the actual use of fasteners. Especially in automobiles, tractors, home appliances, instrumentation, aerospace, communications and other industries and fields are more widely used. However, for threaded fasteners, not only a certain anti-corrosion capability is required in use, but also the interchangeability of threads must be ensured, which can also be called screwability here. In order to meet the dual-use performance of anti-corrosion and interchangeability required by threaded fasteners in use, it is very necessary to formulate special plating standards.
The technical solution adopted by Yueluo to solve its technical problems is: a cabinet with a hidden screw type installation structure. The cabinet includes corner fittings, frame profiles and plates. Connecting slot, the plate installation slot is U shaped, the plate installation slot on the frame profile can be set with one or two, the insertion slot is located on the inner side of the plate installation slot; the main body of the corner fitting is fixed in three directions. The plug connector, the outer side of the plug connector is provided with auxiliary plate installation grooves, and the auxiliary plate installation groove is provided with side baffles; the plug connectors on the corner fittings are correspondingly inserted into the plug connectors on the frame profile, and the cross section of the plug connector Consistent with the cross-sectional size of the corresponding insertion slot, the plate is inserted between the plate installation slots on the frame profile.
DIN6796 Disc Spring Washers (HDS Series) are lock washers designed for bolted and screwed connections. It is designed and manufactured according to DIN 6796 for the connection of medium or high strength bolts and screws. High bearing loads and elastic recovery make the HDS series very effective, and the bolt tension can withstand slack due to: wear of consumables, creep, relaxation, thermal expansion, contraction, or compression of seals. The HDS series increases the elasticity of the screw several times. It can effectively replace the ordinary spring washer, but it is not suitable for the combination of lock washer and flat washer.
Currently, a screw generally includes a shank body, a threaded portion formed on the outer edge of the shank body, and a conical head formed at the rear end of the shank body. When the current thread is in use, since the thread part is cylindrical, the thread part and the workpiece are vertical, so it is relatively laborious when in use, and it is difficult to locate, lock and unlock.
T-slot bolts refer to the bolts installed in the T-slot. The installation process of T-slot bolts is usually as follows. When the T-slot (generally refers to the T-slot aluminum alloy profile) is set horizontally, the bolt The bolt head is placed in the T-slot in the horizontal direction, the bolt shaft is facing outward, and then the bolt is rotated 90 degrees axially, the bolt head becomes vertical and will not come out of the T-slot, and then install the mounting hole of the object Align the bolt rod and insert it and screw the nut on the bolt rod. During the tightening process of the nut, if the thread gap is small or the thread is damaged or there is dirt, the bolt will often rotate, and the rotation angle of the bolt is uncontrollable and impossible. Observe that when the rotation angle of the bolt is in the range of about 90 degrees, the bolt is in a state of being released from the T-shaped groove at any time. Even if the nut is tightened, the installation of the installation object is invalid and unreliable, and there is a serious safety hazard. , the actual situation is that when the rotation angle of the bolt exceeds 20-30 degrees, the installation of the installation object is already unreliable.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: copper nickel-plated fasteners, aluminum column nuts, enlarged and thickened plastic gaskets, hexagon head screws and other products, we can provide you with Provide the right fastener solution for you.
