Service HotlineBuilding aluminum alloy formwork is a new type of building formwork, which conforms to the four sections and one environmental protection policy. It is economical, fast, high-quality and environmentally friendly. Its application is of great significance to building energy conservation and environmental protection. The aluminum template is filled with aluminum template pins. However, the pins in the prior art have low connection strength during use, which is likely to cause the hole to be repaired weakly.
Sprinkle the excess flat washer 6 on the positioning plate II3-1 on the flat washer positioning plate 3, and shake the flat washer positioning plate 3 by hand. After a short time, the flat washer 6 will be positioned and arranged on the upper positioning plate II3-1. In the flat washer hole 3-7, since the width of the opening groove 113-32 of the baffle plate II3-3 is smaller than the diameter of the flat washer hole 3-7, and the thickness of the upper positioning plate II3-1 is designed according to the thickness of the flat washer 6, each Only one flat washer 6 can be accommodated in the flat washer holes 3-7 of each upper positioning plate II3-1, and then use a brush to remove the excess flat washer
In order to overcome the above problems, Guangdong Yueluo Hardware Industry Co., Ltd. provides a screw that can be quickly installed and removed. Using the principle of lever, press the handle downward, and the screw can form a backward force through the connecting piece. Press the screw and nut tightly; lift the handle, the screw forms a forward force, and the screw can be removed. Thus, the time and manpower for screwing during installation and disassembly are reduced. The solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is that the entire screw includes a screw rod, a nut, a connecting piece, a circlip, a positioning pin, a small shaft, a fixed piece, a base, and a handle; the screw is connected by the small shaft at the upper end. At the upper end of the connecting piece, the handle is connected to the lower end of the connecting piece, and the front end of the handle is connected to the base fixing piece through a positioning pin. There are gaps at both ends of the small shaft, and the small shaft is installed through the circlip. The front end of the handle can only be rotated on the positioning pin. Due to the lever principle, when the handle is pressed down, it will drive the screw at the front end of the connecting piece, so that the screw generates a backward force and tightens the screw and the nut. On the contrary, when the handle is pulled up, the screw generates a forward force, so that the screw can be easily removed. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is that the quick-opening screw saves the time and labor of repeatedly twisting the nut during installation and disassembly. The installation and removal process is simple.
The inner tooth elastic washer and the outer tooth elastic washer have many sharp elastic warping teeth on the circumference, which are pressed against the supporting surface and can prevent the loosening of the fastener. The inner tooth elastic washer is used under the screw head with smaller head size; the outer tooth elastic washer is mostly used under the bolt head and the nut. The elastic washer with teeth is smaller than the ordinary spring washer, and the fastener is evenly stressed and reliable to prevent loosening, but it is not suitable for frequent disassembly. Wave spring washer GB: GB/T 7246-1987 Wave washer is divided into WG type, WL type, WN type WG type wave washer WG type wave washer is an open elastic washer, which can usually be installed in a small space, such as giving The bearing is prestressed to reduce the noise of the bearing operation and improve the running accuracy and stability of the bearing. In addition, there are a large number of applied materials in electronic appliances, such as carbon steel, stainless steel, copper alloy and so on. WL-type wave washer WL-type wave washer is a lap-type elastic washer, which can usually be installed in a small space, such as prestressing the bearing, reducing the noise of the bearing operation, and improving the running accuracy and stability of the bearing. There are also a large number of applications in electronic appliances. Materials are carbon steel, stainless steel, copper alloy, etc. WN type wave washer WN type wave washer is a multi-layer wave crest overlapping elastic washer. Compared with the WL type, this series is composed of multi-layer materials, so the K value curve under the same compression stroke is flatter than that of the WL type, which is suitable for elastic force. Larger, and the elastic release of the entire working stroke is required to be more uniform. The materials used are carbon steel, stainless steel, copper alloy, etc. Disc spring washer Disc spring washer, also known as Belleville spring washer, was invented by the French Belleville. DIN6796 Disc Spring Washers (HDS Series) are lock washers designed for bolted and screwed connections. It is designed and manufactured according to DIN 6796 for the connection of medium or high strength bolts and screws. High bearing loads and elastic recovery make the HDS series very effective, and the bolt tension can withstand slack due to: wear of consumables, creep, relaxation, thermal expansion, contraction, or compression of seals. The HDS series increases the elasticity of the screw several times. It can effectively replace the ordinary spring washer, but it is not suitable for the combination of lock washer and flat washer. Since the HDS series is a disc spring that can be folded or overlapped. The combination of the butt joint can increase the deformation of the disc spring group, and the combination of the overlapping method can increase the spring force of the disc spring group. The ideal installation method is to flatten as much as possible. The closer it is to the flattened state, the faster the tension torque increases, and the proper bolt tension can be obtained without a torque wrench.
At present, most of the thread locking structures use an integral nut and a matching external thread screw structure. To remove the nut from the screw rod, it must be completely unscrewed along the screw rod, which is time-consuming and labor-intensive. It is more inconvenient to install.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: bakelite hand-tight adjustable screws, toothed washers, ISO7040 hexagon lock nuts, 8.8 grade galvanized hexagon nuts and other products, we can provide You have the right fastener solution for you.
