Service Hotlineflange T-bolt, comprising: a T-bolt including a threaded tooth body and a bolt head fixedly connected to the threaded tooth body; a flange gasket with a plurality of clip teeth, the flange gasket passing through the The plurality of clamping teeth are clamped with the bolt head of the T-bolt. The technical solution of the utility model is that when the groove-type embedded parts are embedded vertically or at a certain angle, the plastic flange of the new T-bolt will help the bolt to be pre-positioned at a certain position of the groove. When multiple T-bolts are used for fixing, Only one worker needs to pre-arrange the bolt positions and then lock the nuts, which greatly improves the construction efficiency.
As one of the screws, self-tapping screws can directly drill holes on the plate to be fixed by themselves and lock them together with the plate to be fixed. They are easy to use and have a good fixing effect, so they are widely used. However, in the prior art, when the screw is perforated on the plate to be fixed, it is prone to skew, which affects the fixing effect and also reduces the aesthetics. To sum up, how to overcome the above-mentioned defects of the screw fixing method in the prior art is a technical problem to be solved urgently by those skilled in the art.
Generally known bolts refer to screws with a larger diameter. According to this statement, the diameter of screws is much smaller than that of bolts. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems.
The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures. There are also two types of locking nuts. One is to use two identical nuts to screw on the same bolt, and a tightening torque is added between the two nuts to make the bolt connection reliable. The other is a special lock nut, which needs to be used together with a lock washer. As shown in FIG. 1, a plastic gasket 2 is arranged in the center of the nut 1 to play a locking effect, but the process is complicated and the production is inconvenient. One is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to apply a thread to the thread. A centripetal force prevents the lock nut from loosening. At present, the lock nut with better quality on the market is inlaid with small copper pieces that are consistent with the thread of the lock nut on the inner surface of the nut, which is used to prevent the radial jacking screw from directly contacting the locked thread and being damaged. By. This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The process is equally complex.
Riveting products provide great convenience for the unilateral connection of sheet parts, fast and efficient connection without bulky installation tools, and produce reliable standard internal and external threads, achieve cold installation after surface treatment, no pollution, is welding Effective alternative to nuts. Main applications: Auto-body, seat belt systems, bumpers, airbag systems, etc. 1. One-way drawing connection 2. Build standard internal and external threads 3. General product range: M3-M124. Materials: Carbon Steel, Stainless Steel, Aluminum 5. High quality air tools - efficient, economical, lightweight and easy to operate. Use the same principle as hand rivet nuts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hollow yin and yang isolation columns, 8.8 hexagon nuts, butterfly thumb screws and bolts, small countersunk head rivet nuts and other products, we can help you Provide the right fastener solution for you.
