Service HotlineBolts or screws and flat washers assemblies GB/T 9074.1-2002 Cross recessed head screws and external serrated lock washers assemblies GB 9074.2-88 Cross recessed pan head screws and spring washers assemblies GB 9074.3-88 Cross recessed pan head screws, springs Washer and flat washer assembly GB 9074.4-88 Cross recessed small pan head screw and flat washer assembly GB 9074.5-88 Cross recessed small pan head screw and large washer assembly GB 9074.6-88 [1] Cross recessed small pan head screw and spring washer Assembly GB 9074.7-88 Cross recessed pan head screw, spring washer and flat washer assembly GB 9074.8-88 Cross recessed countersunk head screw and conical lock washer assembly GB 9074.9-88 Cross recessed countersunk head screw and conical lock Tight washer assembly GB 9074.10-88 Cross groove hexagon head bolt and flat washer assembly GB 9074.11-88 Cross groove hexagon head bolt and spring washer assembly GB 9074.12-88 Cross groove hexagon head bolt, spring washer and flat Washer assembly GB9074.13-88 Hexagon head bolt and spring washer assembly GB 9074.15-88 Hexagon head bolt and external serrated lock washer assembly GB 9074.16-88 Hexagon head bolt, spring washer and flat washer assembly GB 9074.17-88 From Tapping screw and flat washer assembly GB /T 9074.18-2002 Cross recessed hexagon head self-tapping screw and flat washer assembly GB 9074.20-88 Cross recessed hexagonal head self-tapping screw and large washer assembly GB 9074.21-88 For assembly Spring Washers GB 9074.26-88 External Serrated Lock Washers for Assemblies GB 9074.27-88 Conical Lock Washers for Assemblies GB 9074.28-88.
Bolts refer specifically to screws with larger diameters and may also have no heads, such as stud bolts. In general, it is not called a stud bolt but a stud stud. The most common form of stud is threaded at both ends and a polished rod in the middle. The most typical use: anchor bolts, or places similar to anchor bolts, thicker connections, when ordinary bolts cannot be used.
1. No matter what industry it is, the business is more difficult, and it is still more difficult for the fastener business. After a long period of contact, I realized that the business of making fasteners also requires a lot of attention to be able to do it well. In the business of making fasteners, not just any person can do it, and they all have certain requirements. 2. When it comes to the business of fasteners, no matter what kind of salesperson, the first thing you must have is enough patience, so that we can do this job with confidence, and some customers are not difficult to follow us. Communication, as long as we have enough patience, then we have a greater chance of being able to cooperate with customers on fasteners, and in the face of some relatively large fastener customers, sometimes it is not that we can get it all at once , Sometimes if you want to cooperate, you need to go through multiple contacts to promote a cooperation, so as a salesperson, enough patience is essential. 3. Then, as a fastener salesman, what you need to have is perseverance. Sometimes the salesperson is difficult at work. At this time, you need to adjust it in time, so it will not lead to the phenomenon of giving up easily, after all As a salesman, only through our own efforts can we have the opportunity to receive orders for fasteners from customers. What we need is to be able to face difficulties and move forward bravely. 4. The most important thing for fastener salesmen is to pay attention to details. If we can do a good job in the details, then sometimes we are not far from success. The above are several requirements that need to be met in the fastener business.
Spring mattresses and spring seat cushions are modern and commonly used furniture products with better performance, and their cushion cores are composed of springs. It makes full use of the advantages of good spring elasticity, good support, strong air permeability and durability. The traditional spring pad is a spring with a thicker wire diameter, which is connected and fixed by steel wires, and has high hardness. Most of the elders of the older generation often use linked spring beds, but if they sleep in a fixed position for a long time or are accustomed to sitting on the side and corners of the bed, or flip the mattress irregularly, it is easy to cause depression and elastic fatigue.
The main operation method of the embedded knurled copper nut of the lock nut is injection molding. After heating, it is embedded into the plastic part or directly injection molded. If injection molding is used, the melting point of P/NYLOY/PET is above 200°C. , After the embedded nut is hot melted into the plastic part, the temperature rises rapidly. After injection molding, the plastic body rapidly cools and crystallizes and hardens. If the embedded nut temperature is still at a high temperature, it may fall to the place where the copper nut contacts the plastic part. Start to loosen or crack. Therefore, copper nuts are used instead of carbon steel nuts in the injection molding of embedded nuts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: circuit board support columns, cross-shaped grooves, furniture nuts, plywood nuts, T97.3 gaskets and other products, we can provide you with products suitable for you fastener solutions.
