Service HotlineIn the repair process of the EDITION 700 gearbox, it is often necessary to replace the piston seal. When replacing the direct gear piston seal, the shaft spring retaining ring on it must be removed before the piston can be taken out for replacement. For the seal, since the piston return spring 3 presses the retaining ring 5 through the spring seat 4 (as shown in Figure 3), it cannot be taken out directly. It is necessary to press down the spring seat before taking out the retaining ring. Without special tools, it is not easy to remove the retaining ring. At present, it is a time-consuming, labor-intensive and unsafe job that requires multiple people to use a screwdriver and a prying board to forcefully squeeze and pry to remove the retaining ring.
slotted screw comprises a screw rod, one end of the screw rod is connected to the middle of the bottom surface of the screw head, the side wall of one end of the screw rod away from the screw head is provided with a screw slot in the vertical direction, the screw The bottom surface of the head is in seamless contact with the top surface of the buffer wear-resistant pad, the buffer wear-resistant pad is connected with the screw rod by threads, and the buffer wear-resistant pad is provided with several shock-absorbing holes equally spaced along the circumference.
The core rivet is another type of single-sided riveting. When riveting, the head of the rivet is hit with a hammer to expose the core, so that it is flush with the end face of the nail head, that is, the riveting operation is completed, which is very convenient, especially suitable for inconvenient Riveting occasions using ordinary rivets (which must be riveted from both sides) or blind rivets (lack of a rivet gun). Usually use flat head rivets, countersunk head rivets are suitable for occasions where smooth riveting is required on the surface. Some rivets can also be matched with clothing, becoming a popular element today, mostly the representative of punk style. In addition, there are paired rivets, which are special. Divided into two parts, the thicker section of the rod with a cap has a hole in the center, and the other section of the rod with a cap is an interference fit. When riveting, drive the thin rod into the thick rod.
The force condition of the screw is broadcasted: 1) Self-weight G; 2) Torque M required to overcome material resistance; 3) Axial force P generated by material pressure. Screw screw screw is generally scrapped due to long-term wear, the gap between the screw and the barrel is too large and cannot be extruded normally, but there are also examples of damage due to improper design or improper operation. Therefore, the screw should also meet certain strength requirements. 4) The dangerous section of the screw is generally at the smallest thread root diameter in the feeding section. According to material mechanics, for plastic materials, the composite stress is calculated by the third strength theory, and its strength conditions are:
Bolts or screws and flat washers assemblies GB/T 9074.1-2002 Cross recessed head screws and external serrated lock washers assemblies GB 9074.2-88 Cross recessed pan head screws and spring washers assemblies GB 9074.3-88 Cross recessed pan head screws, springs Washer and flat washer assembly GB 9074.4-88 Cross recessed small pan head screw and flat washer assembly GB 9074.5-88 Cross recessed small pan head screw and large washer assembly GB 9074.6-88 [1] Cross recessed small pan head screw and spring washer Assembly GB 9074.7-88 Cross recessed pan head screw, spring washer and flat washer assembly GB 9074.8-88 Cross recessed countersunk head screw and conical lock washer assembly GB 9074.9-88 Cross recessed countersunk head screw and conical lock Tight washer assembly GB 9074.10-88 Cross groove hexagon head bolt and flat washer assembly GB 9074.11-88 Cross groove hexagon head bolt and spring washer assembly GB 9074.12-88 Cross groove hexagon head bolt, spring washer and flat Washer assembly GB9074.13-88 Hexagon head bolt and spring washer assembly GB 9074.15-88 Hexagon head bolt and external serrated lock washer assembly GB 9074.16-88 Hexagon head bolt, spring washer and flat washer assembly GB 9074.17-88 From Tapping screw and flat washer assembly GB /T 9074.18-2002 Cross recessed hexagon head self-tapping screw and flat washer assembly GB 9074.20-88 Cross recessed hexagonal head self-tapping screw and large washer assembly GB 9074.21-88 For assembly Spring Washers GB 9074.26-88 External Serrated Lock Washers for Assemblies GB 9074.27-88 Conical Lock Washers for Assemblies GB 9074.28-88.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: chrysanthemum tooth washers, coarse teeth and fine teeth, 201 stainless steel wing nuts, galvanized rod bolts and other products, we can provide you with suitable fasteners. Firmware Solutions.
