Service HotlineGB/T3103.3-2000 Fastener Tolerance Flat Washers 2 GB/T5286-2001 General Scheme of Flat Washers for Bolts, Screws and Nuts 3 GB/T9074.1-2002 Bolts or Screws and Flat Washers Assemblies 4 GB/T9074. 18-2002 Self-tapping screws and flat washers assemblies 5 GB/T 95-2002 Flat washers C grade 6 GB/T96.1-2002 Large washers A grade 7 GB/T96.2-2002 Large washers C grade 8 GB/T97. 1-2002 Flat washer Class A 9 GB/T97.2-2002 Flat washer chamfered Class A 10 GB/T97.4-2002 Flat washer for screw and washer assemblies 11 GB/T97.5-2002 Flat washer Self-tapping screws and washers assemblies 12 GB/T848-2002 Small washers Class A 13 GB/T5287-2002 Extra large washers Class C 14 GB/T4678.13-2003 Die-casting mold parts Part 13: Push plate washers 15 GB/T4605 -2003 Rolling bearing thrust needle roller and cage assemblies and thrust washers 16 GB/T97.3-2000 Flat washers for pins 17 GB/T18230.5-2000 Flat washers for bolted structures quenched and tempered 18 GB/T9074.5 -2004 Cross recessed small pan head screw and flat washer assembly 19 GB/T9074.20-2004 Cross recessed hexagon head tapping screw and flat washer assembly 20 GB/T3762-1983 Sharp angle sealing washer for ferrule type pipe joint 21 GB/T1231-2006 Specifications for high-strength large hexagon head bolts, large hexagon nuts and washers for steel structures 24 GB/T5649-2008 Lock nuts and washers for pipe joints and washers 27 GB/T10447-2008 Elements and tolerances of semicircular thrust washers for sliding bearings 28 GB/T94.1-2008 Specifications for elastic washers Spring washers 29 GB/T10446-2008 Dimensions and tolerances for full circle thrust washers for sliding bearings 30 GB/ T93-1987 standard spring washer 31 GB/T94.2-1987 elastic washer technical conditions toothed, serrated lock washer 32 GB/T98-1988 stop washer technical conditions 33 GB/T849-1988 spherical washer 34 GB/T850- 1988 Conical Washer 35 GB/T851-1988 Split Washer 36 GB/T852 -1988 Square bevel washer for I-beam 37 GB/T853-1988 Square bevel washer for channel steel 38 GB/T854-1988 Single-ear stop washer 39 GB/T7244-1987 Heavy-duty spring washer 40 GB/T855-1988 Double-ear stop Dynamic washer 41 GB/T7245-1987 Saddle spring washer 42 GB/T7246-1987 Wave spring washer 43 GB/T856-1988 Outer tongue stop washer 44 GB/T858-1988 Stop washer for round nut 45 GB/T859-1987 Light spring washer 46 GB/T860-1987 Saddle elastic washer 47 GB/T861.1-1987 Internal tooth lock washer 48 GB/T861.2-1987 Internal serrated lock washer 49 GB/T862.1-1987 External tooth lock 50 GB/T862.2-1987 External Serrated Lock Washers 51 GB/T955-1987 Wave Elastic Washers 52 GB/T27938-2011 Sliding Bearing Thrust Washers Failure Damage Terms, Appearance Features and Reasons 53 GB/T956.1- 1987 Conical lock washer 54 GB/T956.2-1987 Conical serrated lock washer 55 GB/T28697-2012 Rolling bearing self-aligning thrust ball bearing and self-aligning seat washer Dimensions 56 GB/T9074.2-1988 Cross groove disc Head screw and male serrated lock washer assembly 57 GB/T9074.3-1988 Cross recessed pan head screw and spring washer assembly 58 GB/T9074.4-1988 Cross recessed pan head screw, spring washer and flat washer assembly 59 GB /T9074.7-1988 Cross recessed small pan head screw and spring washer assembly 60 GB/T9074.8-1988 Cross recessed small pan head screw and spring washer and flat washer assembly 61 GB/T9074.9-1988 Cross recessed countersunk Head screw and conical lock washer assembly 62 GB/T9074.10-1988 Cross recessed countersunk head screw and conical lock washer assembly 63 GB/T9074.11-1988 Cross recessed hexagon head bolt and flat washer assembly Parts 64 GB/T9074.12-1988 Cross recessed hexagon head bolt and spring washer assembly 65 GB/T9074.13-1988 Cross recessed hexagon head bolt, spring washer and flat washer assembly 66 GB/T9074.15- 1988 Hexagon head bolt and spring washer assembly 67 GB/T9074.16-1988 Hexagon head bolt and serrated lock washer assembly 68 GB/T9074.17-1988 Hexagon head bolt, spring washer and flat washer assembly 69 GB/T9074 .26-1988 Spring Washers for Assemblies 70 GB/T9074.27-1988 External Serrated Lock Washers for Assemblies 71 GB/T9074.28-1988 Conical Lock Washers for Assemblies 72 GB/T1030-1988 Inner Spherical Washers[1]
1. The taper of the reaming hole should be 90°. It should be guaranteed that it should be less than 90° rather than greater than 90°. This is a key trick. 2. If the thickness of the sheet metal is less than the thickness of the head of the countersunk head screw, you can replace the screw with a smaller size, or it is better to ream a smaller hole instead of reaming the hole to increase the diameter of the bottom hole and cause the parts to not be pressed tightly. 3. If there are multiple countersunk head screw holes on the part, it should be processed more accurately. Once it is drilled crookedly, it will be ugly to assemble, but as long as the error is not large, it can be tightened completely, because when tightening, if the diameter of the screw is not very large. Large (about no more than 8mm), when there is an error in the hole distance, the screw head will be deformed due to the force when it is tightened or it will be tightened.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a new type of open blind rivet suitable for riveting of aluminum Al, steel St, and stainless steel SST sheets with foam material in the middle. The new rivet improves the mandrel process, adopts aluminum mandrel, the head of the mandrel has a pit for easy deformation, and there is a conical stop groove above the breakpoint of the mandrel. The mandrel can be caught by the stopper to prevent the nail head from being exposed. At the same time, lock the core rod not to loosen.
A nut provided by Yueluo. The nut is in the shape of a casing and is provided with a threaded section. One end of the threaded section is provided with a protrusion on the wall of the hole. The nominal size of the segment or the distance from the rear end of the lug to the hole core in the screw-in direction is smaller than the nominal size of the threaded segment.
In the manufacture of fasteners, the correct selection of fastener materials is an important part, because the performance of fasteners is closely related to its materials. If the material is improperly or incorrectly selected, the performance may not meet the requirements, the service life may be shortened, or even accidents or processing difficulties may occur, and the manufacturing cost will be high. Therefore, the selection of fastener materials is a very important link. Cold heading steel is a steel for fasteners with high interchangeability produced by cold heading forming process. Because it is formed by metal plastic processing at room temperature, each part has a large amount of deformation and a high deformation speed. Therefore, the performance requirements of cold heading steel raw materials are very strict. On the basis of long-term production practice and user research, combined with GB/T6478-2001 Technical Conditions for Cold Heading and Cold Extrusion Steel GB/T699-1999 High-Quality Carbon Structural Steel and target JISG3507-1991 Cold Heading Characteristics of Carbon Steel Wire Rod for Steel, taking the material requirements of grade 8.8 and grade 9.8 bolts and screws as an example, the determination of various chemical elements. If the C content is too high, the cold formability will be reduced; if it is too low, the mechanical properties of the parts cannot be met, so it is set at 0.25% - 0.55%. Mn can improve the permeability of steel, but adding too much will strengthen the matrix structure and affect the cold forming performance; when the part is quenched and tempered, it has the tendency to promote the growth of austenite grains, so it should be appropriately improved on the basis of international standards. 0.45 % - 0.80 %. Si can strengthen the ferrite and reduce the cold formability. SP is an impurity element, and their existence will cause segregation along the grain boundary, resulting in the embrittlement of the grain boundary and damage to the mechanical properties of the steel. It should be reduced as much as possible. B. The maximum value of boron content is 0.005%, because although boron element can significantly improve the permeability of steel, it will also increase the brittleness of steel. Excessive boron content is very unfavorable for workpieces such as bolts, screws and studs that require good comprehensive mechanical properties.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head cylinder head screws, instrument handle nuts, non-standard fine-tooth cap and female cap type cap nuts, flat washers and spring washers combination bolts and other products , we can provide you with a fastener solution that suits you.
