Service HotlineA pull rivet, this kind of pull rivet has good installation performance, firm connection and long service life, but the defects are: first, after installation and use, if it is damaged, it cannot be reused; second, it is convenient to disassemble, and it also increases the possibility of theft ,. It is not conducive to safety; 3. There is still the possibility of movement in the circumferential direction of the collar, which will affect the riveting effect.
The earless retaining ring for the hole is mostly installed in the annular groove on the inner wall of the pipe fitting. The outer diameter of this kind of retaining ring is slightly larger than the diameter of the assembly round hole. When assembling, the earless retaining ring needs to be pressed into the pipe fitting. Since the inner wall of the pipe fitting is relatively smooth, the earless retaining ring is easily skewed in the pipe fitting. It needs to be adjusted several times before entering the annular groove, and the assembly efficiency is low.
The circlip lifting and tightening mechanism includes a lifting mechanism and a tightening mechanism; the lifting mechanism includes a lifting cylinder and a ball screw; the output shaft of the lifting cylinder is connected with the ball screw; the ball screw drives the tightening mechanism to achieve up and down move; the tightening mechanism includes a tightening motor, and the output shaft of the tightening motor drives a pinion sleeved on the output shaft to rotate; the pinion drives the largest gear meshed with it to rotate, and the largest gear is driven by The second largest gear meshed with it rotates; the diameter of the first largest gear is the same as that of the second largest gear; the lower ends of the rotating shafts of the first largest gear and the second largest gear are equipped with rotating discs, and each rotating disc is fixedly installed A probe; two probes can be inserted into the two holes of the circlip at the same time, and the circlip can be tightened or loosened as the motor rotates.
Cross recessed pan head screws refer to cross recessed machine wire screws, which are represented by the letters PM. The country stipulates that the thread specification is M1.6-M10, the performance level is 4.8, A-50, A2-70, CU2, CU3 and AL4, H-type and Z-type cross recessed, and the product grade is Class A cross recessed pan head screws . If other technical requirements are needed, they should be selected from the current standards (such as GB/T196, GB/T3106, GB/T3098.1, GB/T3098.6 and GB/T3098.10).
The main technical problem solved by Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a fixing screw for installation, so as to provide a PCB fixing method with convenient operation, reliable connection and low production cost. In order to solve the above-mentioned technical problems, a technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a fixing screw for installation, which includes a screw body, the axial surface of the screw body is formed with extended screw teeth, and the screw body is The bottom has a hemispherical screw tail, the top of the screw body is provided with a screw head, and the upper surface of the screw head is provided with a slot. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the screw body is composed of an upper tapered rod and a lower cylindrical screw rod, and the tapered rod is an inverted cone. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the diameter of the circular upper surface of the inverted cone of the taper rod is equal to the diameter of the screw mounting hole. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the screw further has a washer, the washer is arranged between the screw head and the screw body, and the washer is a cylinder. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the lower surface of the cylindrical washer has a plurality of teeth, and the teeth are along the edge of the connection between the upper surface of the inverted cone of the tapered rod and the washer Ribs formed by extending outwards. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the teeth of the washer are in contact with and pressed against the PCB board. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the protruding strip is an arc-shaped or straight-shaped structure. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the notch opened on the upper surface of the screw head is a slot. [0018] According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the notch provided on the upper surface of the screw head is a cross groove. According to a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the fixing screw is integrally formed with conductive material. Compared with the existing technology, the fixing screws for installation designed by Guangdong Yueluo Hardware Industry Co., Ltd. can not only ensure the accuracy of the PCB installation position, but also can be installed easily and reliably, which greatly reduces the manufacturing cost and waste of metal materials.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Dacromet-plated washers, thin outer hexagon screw caps, B-type GB859 light washers, high-strength thickened nuts and nuts and other products, we can Provide you with the right fastener solution for you.
