Service HotlineThe national standard name of the cross recessed small pan head three-combination screw is the cross recessed small pan head screw, the spring washer and the flat washer assembly. The national label is GB/T9074.8-1988. This 1988 refers to the year, that is, this standard is the standard issued by the country in 1988. The specifications of the cross recessed small pan head three-combination screw, our company's minimum is M2.5, the shortest is 5mm, the largest is M10, and the longest is 90mm. Of course, as customers have higher and higher requirements for small pan head combination screws, or require smaller and longer combination screws. If the quantity is large, or with the development of our company. Buy some advanced combination screw machines. Come and go to meet the higher requirements of our customers.
1. Other names: root nut, anti-loosening nut, nut. 2. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. The lock nut is one of the anti-loosening measures. The anti-loosening effect of the lock nut mainly depends on the interaction force between the nut and the thread of the bolt. There are many ways to improve the interaction force between meshing threads, such as structural improvement of nut threads, nylon roughening of nylon nuts, and surface treatment of threads.
In order to achieve this technical purpose, the plan of Guangdong Yueluo Hardware Industry Co., Ltd. is: a new type of open rivet, including a rivet body and a mandrel, the rivet body and one end of the mandrel are fixedly connected, and the lower end of the rivet body is provided with There is a round table, the top of the mandrel is provided with a nail head pit, the mandrel is provided with a stop groove, the lower side of the stop groove is provided with a mandrel breakpoint, and the mandrel is set on the mandrel. There is a stop ring, the stop ring is located on the lower side of the round table, and the lower side of the stop ring is provided with an assembly warp.
National Standard 1 GB/T3103.3-2000 Fastener Tolerance Flat Washers 2 GB/T5286-2001 General Scheme of Flat Washers for Bolts, Screws and Nuts 3 GB/T9074.1-2002 Bolts or Screws and Flat Washers Assemblies 4 GB/ T9074.18-2002 Self-tapping screws and flat washers assembly 5 GB/T 95-2002 Flat washers C grade 6 GB/T96.1-2002 Large washers A grade 7 GB/T96.2-2002 Large washers C grade 8 GB/ T97.1-2002 Flat washer Class A 9 GB/T97.2-2002 Flat washer chamfered Class A 10 GB/T97.4-2002 Flat washer for screw and washer assemblies 11 GB/T97.5-2002 Flat Washers for self-tapping screws and washer assemblies 12 GB/T848-2002 Small washers Class A 13 GB/T5287-2002 Extra large washers Class C 14 GB/T4678.13-2003 Die-casting mold parts Part 13: Push plate washers 15 GB /T4605-2003 Rolling bearing thrust needle roller and cage assemblies and thrust washers 16 GB/T97.3-2000 Flat washers for pins 17 GB/T18230.5-2000 Flat washers for bolted structures quenched and tempered 18 GB/T9074 .5-2004 Cross recessed small pan head screw and flat washer assembly 19 GB/T9074.20-2004 Cross recessed hexagon head self-tapping screw and flat washer assembly 20 GB/T3762-1983 Sharp angle seal for tube fittings Washers 21 GB/T1231-2006 High-strength large hexagon head bolts, large hexagon nuts, and washers for steel structures Specifications 22 GB/T1230-2006 High-strength washers for steel structures 23 GB/T2861.10-2008 Die guides - Part 10 : Washers 24 GB/T5649-2008 Lock nuts and washers for pipe joints 25 GB/T94.3-2008 Technical conditions for elastic washers Saddle, wave elastic washers 26 GB/T3099.1-2008 Terms of fasteners threaded fasteners , pins and washers 27 GB/T10447-2008 Elements and tolerances of semicircular thrust washers for sliding bearings 28 GB/T94.1-2008 Technical conditions for elastic washers Spring washers 29 GB/T10446-2008 Dimensions and tolerances for full circle thrust washers for sliding bearings 30 GB/T93-1987 standard spring washer 31 GB/T94.2-1987 elastic washer technical conditions toothed, serrated lock washer 32 GB/T98-1988 stop washer technical conditions 33 GB/T849-1988 spherical washer 34 GB/ T850-1988 Cone Washer 35 GB/T851-1988 Split Washer 36 GB/ T852-1988 Square bevel washer for I-beam 37 GB/T853-1988 Square bevel washer for channel steel 38 GB/T854-1988 Single ear stop washer 39 GB/T7244-1987 Heavy spring washer 40 GB/T855-1988 Double lug Stop washers 41 GB/T7245-1987 Saddle spring washers 42 GB/T7246-1987 Wave spring washers 43 GB/T856-1988 Outer tongue stop washers 44 GB/T858-1988 Stop washers for round nuts 45 GB/T859- 1987 Light spring washer 46 GB/T860-1987 Saddle elastic washer 47 GB/T861.1-1987 Internal tooth lock washer 48 GB/T861.2-1987 Internal serrated lock washer 49 GB/T862.1-1987 External tooth Lock Washers 50 GB/T862.2-1987 External Serrated Lock Washers 51 GB/T955-1987 Wave Elastic Washers 52 GB/T27938-2011 Sliding Bearing Thrust Washers Failure Damage Terms, Appearance Features and Reasons 53 GB/T956.1 -1987 Conical Lock Washer 54 GB/T956.2-1987 Conical Serrated Lock Washer 55 GB/T28697-2012 Rolling Bearing Self-aligning Thrust Ball Bearing and Self-aligning Seat Washer Dimensions 56 GB/T9074.2-1988 Cross Groove Pan head screw and external serrated lock washer assembly 57 GB/T9074.3-1988 Cross recessed pan head screw and spring washer assembly 58 GB/T9074.4-1988 Cross recessed pan head screw, spring washer and flat washer assembly 59 GB/T9074.7-1988 Cross recessed small pan head screw and spring washer assembly 60 GB/T9074.8-1988 Cross recessed small pan head screw and spring washer and flat washer assembly 61 GB/T9074.9-1988 Cross recessed Countersunk head screw and conical lock washer assembly 62 GB/T9074.10-1988 Cross recessed half countersunk head screw and conical lock washer assembly 63 GB/T9074.11-1988 Cross recessed pocket hexagon head bolt and flat washer Assembly 64 GB/T9074.12-1988 Cross-recessed hexagon head bolt and spring washer assembly 65 GB/T9074.13-1988 Cross-recessed hexagon head bolt, spring washer and flat washer assembly 66 GB/T9074.15 -1988 Hexagon head bolt and spring washer assembly 67 GB/T9074.16-1988 Hexagon head bolt and serrated lock washer assembly 68 GB/T9074.17-1988 Hexagon head bolt, spring washer and flat washer assembly 69 GB/ T9074.26-1988 Spring washers for assemblies Ring 70 GB/T9074.27-1988 External Serrated Lock Washers for Assemblies 71 GB/T9074.28-1988 Conical Lock Washers for Assemblies 72 GB/T1030-1988 Inner Spherical Washers
① Nominal thread outer diameter (thread specification): divided into metric system and inch system. Metric thread → common specifications are 2; 2.3; 2.5; 2.6; 2.9; 3; 3.1; 3.5; 4; 4.2; 4.5; The unit is mm (millimeters). Inch thread→ Common specifications are 2#;4#;6#;8#;10#;12#;1/4;7/32;5/16;3/8;1/2 ;9/16;3/ 4. The unit is in (inches). ② Number of teeth/pitch: Definition of number of teeth → the number of teeth lines in one inch (25.4mm) length. Pitch Definition → Distance value between two adjacent threads. Conversion of number of teeth and pitch of teeth → pitch of teeth = 1 inch/number of teeth ③Nominal length: divided into metric system and inch system. Metric Nominal Length → Common values are 5, 6, 6.5, 7, 8, 9, 9.5, 10, 11, 12, 13, 14, 15, 16, 18, 19, 20, 21, 25, 28, 30, 31 , 32, 35, 40, 42, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120. The unit is mm (millimeters). Imperial Nominal Length → Common values are 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, 1, 2, 3. Units: in (inches). ④Head type: use letters to indicate the type of head type, please refer to the previous classification of commonly used screw head types. ⑤Tooth type/tail type: Use letters to indicate the type of tooth type/tail type, please refer to the previous Commonly used screw thread/tail type classification. ⑥Groove type: Please refer to the previous section Category of common screw groove types of our company. Cross-slotted or non-slotted (such as punched hexagon head screws) do not need to be marked here, and other groove types need to be described in words. ⑦Special labeling: In general, no labeling is required. When expressing its characteristics, it is described in words at this position. For example: the specification name of the screw is described as 4-0.7x70PM±tooth length 35, which means 4 is the nominal diameter of the screw thread, 0.7 is the pitch, 70 is the nominal length of the screw, and P means its The head type is a pan head, M means its tooth type/tail type is a wire thread type, ± means its groove type is ± groove and can also be expressed by plus or minus groove. Tooth length 35 is special Mark, specify the thread length value of this screw.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: step nuts, production carriage bolts, one round head, one head, square head screws and other products, we can provide you with suitable fastener solutions for you .
